Using Tera Term I am able to access the boot loader of a treo 700p without a serial cable From there I am able to see the phone with chamealon. However i need the spc code to go further anybody know the commands to read the spc off this phone?

I would like to know this,too!

the spc is stored on the modem firmware, however i heard bitbim can read? HOW! lol

still no go with bit pim even with passthrough mode enabled, btw im using usb and may be problem but i can still see and send commands to phone with terminal but anybody know the commands well?
in terminal these are the commands listen with -h

? [command]
h [command]
mb [StartAddr [Count [Filler]]]
mh [StartAddr [Count [Filler]]]
mw [StartAddr [Count [Filler]]]
ppdl [pathname]
l [pathname]
jump [addr]
lr [pathname]
ram start len loop
BatteryEEPROM
sleep
Ledtest
keytest [De-bounce interval]
irtest [tx/rx] [Loop Count] [cir/sir] [icp/std]
BTRouter [speed]
cdmar [OS Mode] [Port] [speed]
RadioRouter [OS Mode] [speed] [PCUart] [RadioUart]
AudioCDMA
audio
Erase startaddress length
Camera [1:CameraInit(1) 2:CameraInit(2)]
usb
sd2r
ram2sd
sd2ram
ruu
wrasv
bootflag
nand [command] [startaddress] [tempbuffer]
map

I do treo 700's all the time with com box and serial cable works just fine for me :) and bitpim

the spc is stored on the modem firmware, however i heard bitbim can read? HOW! lol

Open qpst, detect the phone, close qpst and open bitpim. read nvm... enjoy

I do treo 700's all the time with com box and serial cable works just fine for me :) and bitpim

what cable do you use. where do you get it from. I want one soooooo bad please let me know. if you can post driver too thanks.:)

enjoy:D

The USB cable i use had to be made using 2 different cables. not usre how it was done as i didnt do it, but i know it had to be made.

Open qpst, detect the phone, close qpst and open bitpim. read nvm... enjoy

I already like you say but still cannot connected by QPST because I problem about lock code / password 4 digit, and I don't phone number maybe you help me explain about that,thanks

I already like you say but still cannot connected by QPST because I problem about lock code / password 4 digit, and I don't phone number maybe you help me explain about that,thanks

#*#3424 DIAL
#*#3282 DIAL press ok

#*#3424 DIAL
#*#3282 DIAL press ok

This code for make can connected, but I have problem cannot press any key meaning if we switch on the phone they ask password 4 digits, I don't know phone number that is the problem

This code for make can connected, but I have problem cannot press any key meaning if we switch on the phone they ask password 4 digits, I don't know phone number that is the problem

you need make hard reset. already post in forum.

you need make hard reset. already post in forum.

Thanks for your attention, You mean behind the phone have small hole,right !
I already try,but they still appear again the password ? I already try use USB Cable synchronize they need the password, too.
This is new model Treo 700 WX from sprint

you need make hard reset. already post in forum.

Thanks Sir, Now I already got it

you need make hard reset. already post in forum.


I have problem with internet Treo 700 P from Sprint,they can connected but cannot browsing

I been reading for couple hours now about treo but I still don't get it would I be able to connect my phone to cdma or work shop ?
but how if my phone will not apear as a modem Ai try ##3424 and all but I goes to sync

do I have to make a cable just to change the prl?
please advice about it regards

You first need to make sure you have a serial cable not usb. USB will not work, once you have serial cable, check and see what com port your device manager is set to, whether com 1 or 2, I always use com 1, then detect treo with either SE47 tool or SPC Tool (Looks like Homer Simpson), this will find & give you SPC, once it stops, connect again and your SPC will "Zero Out". Once this is done, use QPST, it's that simply. 100% tested on Treo 650, 700 and others...... Any other questions, get back to me, will help if needed.

:)

where i can buy serial data cablr for treo 700 ,,,,,,,,,,thank you

Can u describe how did u gt spc? Can u post drivrs which u wer using!!!!

Open qpst, detect the phone, close qpst and open bitpim. read nvm... enjoy

Can u describe how did u gt spc? Can u post drivrs which u wer using!!!!

I use serial cable to do this.

I am using and data cable and Unicdma box it is working or it will see but can bot any info. What I suppose to do just read SPC


I use serial cable to do this.

just read it with nv backup from cdmaupdater.. no need serial cable, only sd card... search the forums

I am using and data cable and Unicdma box it is working or it will see but can bot any info. What I suppose to do just read SPC

Yes cable from unicdma box can helpyou, just pt in diag mode a read spc ith bitpim.

@Kocoman post other way you can use too.

diag mode??

Yes cable from unicdma box can helpyou, just pt in diag mode a read spc ith bitpim.

@Kocoman post other way you can use too.

diag mode??

Its already posted in this forum. Just your handset and computer, even cable is not required.

I have spc , but i cant enter nam program with 6 spc digts , anyone can help??


just read it with nv backup from cdmaupdater.. no need serial cable, only sd card... search the forums