Is there any istructions or a guide on how this can be done! i have searched and searched, posted everywhere. Still no helP. please let us know!

i will help u to make ur treo 700 work in cricket but can i know what carrier is it pls ,verizon alttel ,sprint?

its on sprint, please let me know i would really appreciate it.

let me know

Can you make this information available to the forumn:

I will help u to make ur treo 700 work in cricket but can i know what carrier is it pls ,verizon alttel ,sprint?

Can you make this information available to the forumn:

I will help u to make ur treo 700 work in cricket but can i know what carrier is it pls ,verizon alttel ,sprint?

I have a Verizon Treo 700 and would like to know how to change it to Cricket..

weve been doing these for a while on hofo, but i havent been lucky yet if anyone has instructions please post or pm me

first dont forget to put thank .

dial *22807 the prl will be cricket ,call cricket do esn change ,when the operation done ,dial again *22807 and ur treo will work in cricket ,enjoy it :) .

:) dont forget to put thx.
about alttel same verizon ,i posted it ,about sprint use bitpim to read spc ,or kyocera phonetom spc rader to read spc ,to load prl use qpst ,enjoy it .

Can you make this information available to the forumn:

I will help u to make ur treo 700 work in cricket but can i know what carrier is it pls ,verizon alttel ,sprint?

i have a sprint 700wx how do i flash it to cricket?

thanks

i have a sprint 700wx how do i flash it to cricket?

thanks

Same here... any help would be appreciated.

Thanks

You cant actually flash a full firmware version to the treo as I believe cricket never carried it. You can get it on the network but the internet and mms features dont work without some serious hacking first.

Thank for that! we all know it only make calls, the thing here is how to flash the phone, the pc can see the phone, but does not appear to be on any com in order to communicate with software any help on that?

i need help for flshing treo 700p to 700w

Same here... any help would be appreciated.

Thanks

how would i turn my sprint 700p to cricket

please help me change my 700p to cricket

here's my guide, I've worked on them, they are simple to and easy:

1) Set phone to Pass Through Mode (DIAG) by entering ##3424# or #*#3424#

2) Using UNIBOX connect through RS232 set to 5V FS OFF and MODE FBUS.

3) Detect Phone with QPST first, then exit QPST, and start BITPIM

4) Configure correct port and read file system. Retrieve nvm > nvm_security or nvm_002 file

5) Search for 6 digit codes, two should be found (SPC and MSL)

6) Using QXDM (ensure VIEW is set to COMMAND OUTPUT) type the following commands:

a) spc "******"
Replace asteriks with the 6 digit code. Output should read successful.

b) pr_list_wr 0 "C:\prl_1039.prl"
If needed change file path to location of PRL. Output should read successful.

c) nv_write sec_code {"000000"}
Optional: use this command to change code to zeros or another 6 digits.

7) Enter ##3424# to exit DIAG mode and reboot phone.

8) NAM Programming by ##MSLCode#


----------------------

By the way, step 2 is for those who use a unibox like device to plug the phone in, but it could be different for you.

There's many methods to retrieve SPC, flash prl, but I prefer QXDM or CDMA WORKSHOP, they both work without a problem on TREO

I have problem with cricket wap on 700wx VRZ. I put Simple IP only, I put cricket wap like Moto Q way. When I turn phone to offline mode or turn off, after this my wap is going Broadband access VRZ. Then i need to do hard reset to get cricket wap back :(:(

I am looking for a source for monster flash files. I already searched humpa.com, I am looking for files for PDA's such as Treo, and Moto Q. I already flash v3c , v3m razr's, krzr km1. Does any one has sources for other monster files? I know cricket stores are full flashing these phones so I felt that the files have got to be out there somewhere. Any advice??
Thanks

there are no monster flash files. A monster flash file are only out there for the phones that cricket once carry. The closest to a monster file for a non cricket model was the w385 cricket upgrade. If you want wap and mms to work on those phone I recommend taken it to a shop to have it full flashed.

Can u help me with 700W treo to work on cricket service

I bought a special RS-232 cable to connect a Palm Treo 700W so that I could change the PRL using QPST, but the phone isn't detected on COM1 in "QPST Configuration".

I have set the phone into Diagnostic mode using the #*#3424 command and it says "Diag Mode is now Active".

When connected and I run the DIAG command a second time as proscribed, an error will display on the phones screen that it "Could not open Com" which is followed by a second message saying "Could not open DBG"

Any clue why this is happening?

Okay- it was the cable I was using. I bought another cable from a different manufacturer and it works perfectly.

FYI- the working cable is PDCT5-H9 which was purchased from ...

Hi all,
To change Treo 700 from Sprint to another carrier ,you 'll need to change some parameters like:
- MCC :Mobile country code
- MNC: mobile Network code
- System ID:
- Network ID:defualt 65535

you can change them by using ##DATA# ,then select Advance .
It'll ask you for MSL or SPC .

you can find the SPC or MSL by using GetSPC.in attached file.
and finally use the ##SPC# to change MSID or MIN.

here's my guide, I've worked on them, they are simple to and easy:

b) pr_list_wr 0 "C:\prl_1039.prl"
If needed change file path to location of PRL. Output should read successful.



I tried this and qxdm gives me
18:08:51.275 pr_list_wr 0 "C:\prl_00069.prl"
18:08:51.275 pr_list_wr - Obsolete command


what's the problem?

Anybody here have this going on a Treo 700w yet so they can help me.
I'm trying to flash it as soon as possible.

Anybody here have this going on a Treo 700w yet so they can help me.
I'm trying to flash it as soon as possible.

its been done, check the forum, do a quick search, please try to search first, if you still cant find the thread then PM me but we try to encourage everyone to use SEARCH, thanks

Treo FLASHING:

Step 1: Connect serial cable to back of computer with null modem adapter and gender adapter in order to connect properly

Step 2: Go into you device manager and look under PORTS, SEE what com # is the communications port under

Step 3: Start up QPST configuration....(usually communication port is under com1)

Depending on the treo model you are using you will need to put the phone into passthrough mode, which enables the data
interface of the phone. You need to do this in order for qpst to read it

Sprint Treos's (600,650,700)

##3424#
or
##3424

Verizon Treos's (600,650,700)

#*#3424*
#*#3424
##3424

Depending on what OS it is running you will either have a "passthrough enabled" box that pops up for PALM OS or a DIAG
Mode screen with WM5 devices. The phone might not be able to go right into passthrough with the WM5 treos, they sometimes
have to reset and then re-enter the passthrough code to enable it. With Treos with the PALM OS interface to diable the passthrough
re-enter the passthrough code and a window will pop saying "passthrugh disabled" YOU NEED TO DO THIS AFTER FLASHING !

Step 4: With the phone now in passthrough connect the serial cable now. You now should see under QPST configuration the phone pop
up....and flash as normaly

TO FLASH: After loading the phone onto qpst under qpst configuration, select the phone and select start clients

step 5: select Service programing

step 6: hit ok and select the roam tab

step 7: there will be a box that say preferred roaming and a file box

step 8: select browse and select the prl file that is on the cd (1040 prl)

step 9: select the phone tab on top of your screen, select write to phone

step 10: a box will be asking for spc, type in 000000 and ok, let fully load

step 11: After loading disconnect phone and disable passthrough mode and your done !


----------------------------------------------------------------------------------------------------------------------------------------

Obtaing spc's FOR SPRINT TREOS:

Step 1: Start up Bitpim...

Step 2: Let load untill you see a window that pops up reading "phone detection failed" and select YES under run settings...

Step 3: The new window that pops up is where you select the settings only change the following:

- under PHONE TYPE: select Other CDMA Phone
- were com port is select browse...
- a new window will appear...let load
- Under AVAILABLE PORTS: select your treo phone (your com number will be here)
- select ok...

Step 4: Under BitPim Settings select ok again...

Step 5: GO to the view tab, select "view filesystem", you then will see Filesystem in the right hand coloum

Step 6: Select filesysem from the coloum, select the file the and let load...

Step 7: select the + NVM folder...select NVM folder

Step 8: Select and open nvm_0000 or nvm_0001 and so on untill you see the spc with WM5 treos, it will be a nvm security file

Step 9: Inside the nvm files you now will see the contents of the folder, around the middle of the file you will see two 6 digit numbers
something like 323424.....145343...and the Sprint name... WRITE down both those six digit numbers and those are your spc's, try using the
first one, if it does not work...use the secondone (go through each nvm folder untill you can find this, it is usually under the 0, 1, 2, or
3 nvm folders or security folders with WM5 Treos...

Step 10: Exit out of bitpim and load up qpst, and flash.... REMEMBER to change the spc all to 000000 in qpst so in case you need to access
the phone again you can without going through these steps again. (IN QPST serivice programming under the settings tab there will be code box,
this is were you need to change the codes to all 000000)

With the orginal SPC you extracted from bitpim remember to select phone, then READ FROM PHONE and type in the spc. All of the phones info will
load up....

----------------------------------------------------------------------------------------------------------------------------------------

Setting Up-Web on WM5 Treo Devices:

Step 1: when phone comes back on go to settings> connections>connections...under my work network hit add new modem connection..

Step 2: you can name it whatever you want...make sure the modem says cellular line

Step 3: hit next the phone number is #777 and hit next

Step 4: for user name put (the customer phone number with area code)@mycricket.com...password is cricket

Step 5: leave domain blank..and hit finish now go back to your connections and hit edit proxy server.

Step 6: select the box that says this network connects to the internet....and select the box under it too..

Step 7: were it says proxy server : put Wap.mycricket.com...then hit advanced..

Sterp 8: there are going to be 4 different proxys here...click on the HTTP one..

Step 9: for the proxy put in Wap.mycricket.com....and where it say port put 8080...hit ok and do the same thing to the other 3..

Step 10: hit ok and got back to your connections...and click on the tabs that says advance...and hit select networks and make sure that
My work network is used when programs connect to the internet..
(it might not be named My work network, just select the connection name that you made)

Step 11: close all of that stuff out and go to internet explorer...and type in [Only Registered Users Can See Links]
...then its going to connect...and it should got to the portal.....

Step 12: since you cant do much with the portal....type in this [Only Registered Users Can See Links]
and search for the website you want to go to and this will let you do it.....

WITH the 700wx from SPRINT web is not able to work....the VERIZON 700w you will need to go to settings, connections, the advance tab and
under dialing rules, uncheck dialing rules (so your not using them) ALSO you will need to load the phone up in qpst and under the data tab select simple
ip only and write it to the phone....

----------------------------------------------------------------------------------------------------------------------------------------

Setting Up-Web on Treos w/PALM OS:

Step 1:

Go to PREFS in on your treo, network

Step 2:

Change the service to : MYCRICKET or mycricket

Step 3:
Connection: High Speed Wireless

Step 4:
User Name: (your phone number with area code) @ mycricket.com

Step 5:
Passward (make it) : cricket (ALL lower case, make sure)

Step 6:
Go to details and uncheck mobile IP.......
LEAVE ip address checked ! & LEAVE Query DNS checked !

NEXT steps are required for you to go into the web browser

Step 7:
Click browser, go to options then down to prefs

Step 8:
Make the home page to exactly the following:
[Only Registered Users Can See Links]

Step 9:
Go to advanced tap and click use custom proxy.....click it and make it exactly
wap.mycricket.com and make the port: 8080

Step 10:
Load up web and your done ! Give it time if it is loading......let it fully recive and after you should have your cricket page with the green backround.
your done!

Portal to google (in order to go to any other website):

[Only Registered Users Can See Links]

ON THE SPRINT 700p you need to go to the dialing page to get into the prefs in order to change the network settings (allows you to modify it) .... You
cannot modify the network settings just going to the main menu and going to prefs then network...(it will not let you modify it for some reason)

Also if you are having problems because it says "locked" just go into the menu, edit, and then select modify and it will ask you if its alright to change,
select yes. Now unlocked

-------------------------------------------------------------------------------------------------------------------------------------------

ACTIVATING phone:

#*#000000# For Manual programing Verizon Treo
##000000# For Manual programing Sprint Treo
verizon: plug in esn in crickets system, *228
sprint: After changing SPC to 000000, dial ##000000# and plug the cricket phone number for MDN and MIN number for MSID and select done (reset)

-------------------------------------------------------------------------------------------------------------------------------------------


Dont Forget To Say Thankx:)

hi everyone...am a new member in this community...i hope to learn a few tricks and hope to contribute some of my own as well...

here's my guide, I've worked on them, they are simple to and easy:

1) Set phone to Pass Through Mode (DIAG) by entering ##3424# or #*#3424#

2) Using UNIBOX connect through RS232 set to 5V FS OFF and MODE FBUS.

3) Detect Phone with QPST first, then exit QPST, and start BITPIM

4) Configure correct port and read file system. Retrieve nvm > nvm_security or nvm_002 file

5) Search for 6 digit codes, two should be found (SPC and MSL)

6) Using QXDM (ensure VIEW is set to COMMAND OUTPUT) type the following commands:

a) spc "******"
Replace asteriks with the 6 digit code. Output should read successful.

b) pr_list_wr 0 "C:\prl_1039.prl"
If needed change file path to location of PRL. Output should read successful.

c) nv_write sec_code {"000000"}
Optional: use this command to change code to zeros or another 6 digits.

7) Enter ##3424# to exit DIAG mode and reboot phone.

8) NAM Programming by ##MSLCode#


----------------------

By the way, step 2 is for those who use a unibox like device to plug the phone in, but it could be different for you.

There's many methods to retrieve SPC, flash prl, but I prefer QXDM or CDMA WORKSHOP, they both work without a problem on TREO
i have a sprint treo 700 wx, i am flashing it to cricket and when ever i go into the ##diag# it doesnt recognize it on my PC. through QPST or CDMA workshop. please help??? will active sync be messing it up?

qpst does not detect my verizon 700w phone in diag mode

I have found and followed similar instructions in other threads and I have been able to have the Treo 755p fully flashed working on Cricket "Except MMS" . Talk-text-wap all working well but for some reason when sending a picture (using the txt plus adding a pic) errors come up and does not work. Usually on other phone models such LG,Sam,etc. One needs to go and configure manually the "mms.mycricket.com" or /servlets/mms. I cannot find this MMS settings under pref/connections. I think I am missing this veryimportant step. Can anyone direct me where to find it or what am I missing?
Appreciated...Thank you




Treo FLASHING:

Step 1: Connect serial cable to back of computer with null modem adapter and gender adapter in order to connect properly

Step 2: Go into you device manager and look under PORTS, SEE what com # is the communications port under

Step 3: Start up QPST configuration....(usually communication port is under com1)

Depending on the treo model you are using you will need to put the phone into passthrough mode, which enables the data
interface of the phone. You need to do this in order for qpst to read it

Sprint Treos's (600,650,700)

##3424#
or
##3424

Verizon Treos's (600,650,700)

#*#3424*
#*#3424
##3424

Depending on what OS it is running you will either have a "passthrough enabled" box that pops up for PALM OS or a DIAG
Mode screen with WM5 devices. The phone might not be able to go right into passthrough with the WM5 treos, they sometimes
have to reset and then re-enter the passthrough code to enable it. With Treos with the PALM OS interface to diable the passthrough
re-enter the passthrough code and a window will pop saying "passthrugh disabled" YOU NEED TO DO THIS AFTER FLASHING !

Step 4: With the phone now in passthrough connect the serial cable now. You now should see under QPST configuration the phone pop
up....and flash as normaly

TO FLASH: After loading the phone onto qpst under qpst configuration, select the phone and select start clients

step 5: select Service programing

step 6: hit ok and select the roam tab

step 7: there will be a box that say preferred roaming and a file box

step 8: select browse and select the prl file that is on the cd (1040 prl)

step 9: select the phone tab on top of your screen, select write to phone

step 10: a box will be asking for spc, type in 000000 and ok, let fully load

step 11: After loading disconnect phone and disable passthrough mode and your done !


----------------------------------------------------------------------------------------------------------------------------------------

Obtaing spc's FOR SPRINT TREOS:

Step 1: Start up Bitpim...

Step 2: Let load untill you see a window that pops up reading "phone detection failed" and select YES under run settings...

Step 3: The new window that pops up is where you select the settings only change the following:

- under PHONE TYPE: select Other CDMA Phone
- were com port is select browse...
- a new window will appear...let load
- Under AVAILABLE PORTS: select your treo phone (your com number will be here)
- select ok...

Step 4: Under BitPim Settings select ok again...

Step 5: GO to the view tab, select "view filesystem", you then will see Filesystem in the right hand coloum

Step 6: Select filesysem from the coloum, select the file the and let load...

Step 7: select the + NVM folder...select NVM folder

Step 8: Select and open nvm_0000 or nvm_0001 and so on untill you see the spc with WM5 treos, it will be a nvm security file

Step 9: Inside the nvm files you now will see the contents of the folder, around the middle of the file you will see two 6 digit numbers
something like 323424.....145343...and the Sprint name... WRITE down both those six digit numbers and those are your spc's, try using the
first one, if it does not work...use the secondone (go through each nvm folder untill you can find this, it is usually under the 0, 1, 2, or
3 nvm folders or security folders with WM5 Treos...

Step 10: Exit out of bitpim and load up qpst, and flash.... REMEMBER to change the spc all to 000000 in qpst so in case you need to access
the phone again you can without going through these steps again. (IN QPST serivice programming under the settings tab there will be code box,
this is were you need to change the codes to all 000000)

With the orginal SPC you extracted from bitpim remember to select phone, then READ FROM PHONE and type in the spc. All of the phones info will
load up....

----------------------------------------------------------------------------------------------------------------------------------------

Setting Up-Web on WM5 Treo Devices:

Step 1: when phone comes back on go to settings> connections>connections...under my work network hit add new modem connection..

Step 2: you can name it whatever you want...make sure the modem says cellular line

Step 3: hit next the phone number is #777 and hit next

Step 4: for user name put (the customer phone number with area code)@mycricket.com...password is cricket

Step 5: leave domain blank..and hit finish now go back to your connections and hit edit proxy server.

Step 6: select the box that says this network connects to the internet....and select the box under it too..

Step 7: were it says proxy server : put Wap.mycricket.com...then hit advanced..

Sterp 8: there are going to be 4 different proxys here...click on the HTTP one..

Step 9: for the proxy put in Wap.mycricket.com....and where it say port put 8080...hit ok and do the same thing to the other 3..

Step 10: hit ok and got back to your connections...and click on the tabs that says advance...and hit select networks and make sure that
My work network is used when programs connect to the internet..
(it might not be named My work network, just select the connection name that you made)

Step 11: close all of that stuff out and go to internet explorer...and type in [Only Registered Users Can See Links]
...then its going to connect...and it should got to the portal.....

Step 12: since you cant do much with the portal....type in this [Only Registered Users Can See Links]
and search for the website you want to go to and this will let you do it.....

WITH the 700wx from SPRINT web is not able to work....the VERIZON 700w you will need to go to settings, connections, the advance tab and
under dialing rules, uncheck dialing rules (so your not using them) ALSO you will need to load the phone up in qpst and under the data tab select simple
ip only and write it to the phone....

----------------------------------------------------------------------------------------------------------------------------------------

Setting Up-Web on Treos w/PALM OS:

Step 1:

Go to PREFS in on your treo, network

Step 2:

Change the service to : MYCRICKET or mycricket

Step 3:
Connection: High Speed Wireless

Step 4:
User Name: (your phone number with area code) @ mycricket.com

Step 5:
Passward (make it) : cricket (ALL lower case, make sure)

Step 6:
Go to details and uncheck mobile IP.......
LEAVE ip address checked ! & LEAVE Query DNS checked !

NEXT steps are required for you to go into the web browser

Step 7:
Click browser, go to options then down to prefs

Step 8:
Make the home page to exactly the following:
[Only Registered Users Can See Links]

Step 9:
Go to advanced tap and click use custom proxy.....click it and make it exactly
wap.mycricket.com and make the port: 8080

Step 10:
Load up web and your done ! Give it time if it is loading......let it fully recive and after you should have your cricket page with the green backround.
your done!

Portal to google (in order to go to any other website):

[Only Registered Users Can See Links]

ON THE SPRINT 700p you need to go to the dialing page to get into the prefs in order to change the network settings (allows you to modify it) .... You
cannot modify the network settings just going to the main menu and going to prefs then network...(it will not let you modify it for some reason)

Also if you are having problems because it says "locked" just go into the menu, edit, and then select modify and it will ask you if its alright to change,
select yes. Now unlocked

-------------------------------------------------------------------------------------------------------------------------------------------

ACTIVATING phone:

#*#000000# For Manual programing Verizon Treo
##000000# For Manual programing Sprint Treo
verizon: plug in esn in crickets system, *228
sprint: After changing SPC to 000000, dial ##000000# and plug the cricket phone number for MDN and MIN number for MSID and select done (reset)

-------------------------------------------------------------------------------------------------------------------------------------------


Dont Forget To Say Thankx:)

first dont forget to put thank .

dial *22807 the prl will be cricket ,call cricket do esn change ,when the operation done ,dial again *22807 and ur treo will work in cricket ,enjoy it :) .

will this work for metropcs?

Hi all,
To change Treo 700 from Sprint to another carrier ,you 'll need to change some parameters like:
- MCC :Mobile country code
- MNC: mobile Network code
- System ID:
- Network ID:defualt 65535

you can change them by using ##DATA# ,then select Advance .
It'll ask you for MSL or SPC .

you can find the SPC or MSL by using GetSPC.in attached file.
and finally use the ##SPC# to change MSID or MIN.

Thanks for the info. I do need to get my SPC. I'm sure this will work on my Treo 700p. I DL'd the files and extracted but what do I do with them?

They don't run in windows and I assume they wo't run or even copy to the palm.:confused:

Hello I'm looking for help on flashing a sprint palm treo 755p to cricket...it has been flashed but I tried to update it and ever since it hasn't worked. Now my text will work but I can't make any calls and no one can call me either. Not to mention the fact that my web or pic mail will work either. If there is anyone who can help I would appreciate.

:confused:

Did you call cricket Customer service????...if not just call them to refresh you account okay

How's everyone doin' today? I have a quick question maybe someone can help me out with.....I have a verizon treo 700wx that was given to me from a friend. In reading this forum, I see all you have to do is press *22807 and it will work. Does that include internet and email? Any info on the subject will be greatly appreciated. Thank you!!:cool: