I have put the Sprint PPC6700SP in Diag Mode and press start. I have downloaded drivers from this forum, but I cannot get them to load. I have also tried to modify the drivers as outlined below and still have not got them to work. Please advise

-------------------------------------

What to do: (Explaination in NEXT post)
1. download the "Qualcomm (PID:3197) Drivers" from: [Only Registered Users Can See Links]
2. extract the above ZIP file to a empty folder
3. goto extracted folder and edit BOTH the "qcmdm2k.inf" AND "qcser2k.inf" files:
qcmdm2k.inf [Models] section:
CHANGE:
%QUALCOMM02% = Modem2, USB\VID_05C6&PID_3197&MI_00
TO SAY:
%QUALCOMM02% = Modem2, USB\VID_0BB4&PID_0B03&MI_00

qcser2k.inf [QcomSerialPort] section:
CHANGE:
%QcomDevice% = QportInstall, USB\VID_05C6&PID_3197&MI_01
TO SAY:
%QcomDevice% = QportInstall, USB\VID_0BB4&PID_0B03&MI_01

4. UNINSTALL and REMOVE ALL ATTEMPTS with other drivers
5. UNPLUG your phone from USB
6. put phone in DIAG mode #3424 and click START
7. plug phone USB back into computer
8. two "Found New Hardware" wizards come up, point both to the directory where the NEW inf files AND drivers are
9. look in "Device Manager" in "Devices by connection" mode for a chain of THREE devices off your USB port: ("Composite USB Device", "Qualcomm Proprietary USB Modem (PID 3197)", "Qualcomm Diagnostics Interface") If you find ALL THREE of these with NO RED X's or YELLOW !'s your good
10. start QPST Config and ADD the DIAG port (second of two NEW COM ports)
11. Start the program you want (ie. Service Programming, EFS Explorer) and select the COM port you just setup (NOT WORK OFFLINE mode) to read in settings from your phone.
12. now HAVE FUN

I have put the Sprint PPC6700SP in Diag Mode and press start. I have downloaded drivers from this forum, but I cannot get them to load. I have also tried to modify the drivers as outlined below and still have not got them to work. Please advise

-------------------------------------

What to do: (Explaination in NEXT post)
1. download the "Qualcomm (PID:3197) Drivers" from: [Only Registered Users Can See Links]
2. extract the above ZIP file to a empty folder
3. goto extracted folder and edit BOTH the "qcmdm2k.inf" AND "qcser2k.inf" files:
qcmdm2k.inf [Models] section:
CHANGE:
%QUALCOMM02% = Modem2, USB\VID_05C6&PID_3197&MI_00
TO SAY:
%QUALCOMM02% = Modem2, USB\VID_0BB4&PID_0B03&MI_00

qcser2k.inf [QcomSerialPort] section:
CHANGE:
%QcomDevice% = QportInstall, USB\VID_05C6&PID_3197&MI_01
TO SAY:
%QcomDevice% = QportInstall, USB\VID_0BB4&PID_0B03&MI_01

4. UNINSTALL and REMOVE ALL ATTEMPTS with other drivers
5. UNPLUG your phone from USB
6. put phone in DIAG mode #3424 and click START
7. plug phone USB back into computer
8. two "Found New Hardware" wizards come up, point both to the directory where the NEW inf files AND drivers are
9. look in "Device Manager" in "Devices by connection" mode for a chain of THREE devices off your USB port: ("Composite USB Device", "Qualcomm Proprietary USB Modem (PID 3197)", "Qualcomm Diagnostics Interface") If you find ALL THREE of these with NO RED X's or YELLOW !'s your good
10. start QPST Config and ADD the DIAG port (second of two NEW COM ports)
11. Start the program you want (ie. Service Programming, EFS Explorer) and select the COM port you just setup (NOT WORK OFFLINE mode) to read in settings from your phone.
12. now HAVE FUN

here you go this should work for you it took me days to find these when i first needed them so i know how hard it is to find

go to:

[Only Registered Users Can See Links]

look for connection manager for :

Sprint PCS Connection 26MB 3.07.043 Download
Manager for Phone as
Modem/USB Cables

got me up and tweaking

I killed my phone by flashing firmware, now phone totaly dead.
But when I plug in to usb, i'ts looking for some usb driver, any body has any idea what it may be:eek:
I do have all diagnostic drivers they will work only if phone works in diag mode.
This is needs to be some factory:eek::eek:drivers:eek::eek:

I killed my phone by flashing firmware, now phone totaly dead.
But when I plug in to usb, i'ts looking for some usb driver, any body has any idea what it may be:eek:
I do have all diagnostic drivers they will work only if phone works in diag mode.
This is needs to be some factory:eek::eek:drivers:eek::eek:

you are probably right...most cdma phones can still load fw from bootloader even if you have totally crashed it...see if you can put your 6700 into bootloader mode...if so and your drives still don't work, look for a bootloader driver...this may be a good approach or may be a waste of time...however- if you can get into bootloader mode then you can definitely get a new rom on there...

good luck :)

I flashed and bricked mine and just had to flash it from the minisd. Found the process form another site, but it worked.

I flashed and bricked mine and just had to flash it from the minisd. Found the process form another site, but it worked.

can you post link to the site that has the steps for flashing from sd card...would be helpful to many i'm sure...

thnx

[Only Registered Users Can See Links]
[Only Registered Users Can See Links]

The second site was related to tryin gto update my phone to wm6, and i GOT stuck in a bad way. Bad flash card...

Running WM6now after a successful flash with a good card.

Hope this helps... If you can't get to the boot loader though...yeah...spare parts?