Nokia 6131 весит на заставке нокия и белый экран

[asrar]

Принесли NOKIA 6131 весит на заставке и потом белый экран попробул прошишь непомогло думаю что флешка битая но в остальном нужен совет коллег.
вот лог обшей продцедуры

Скрытый текст: Показать

Handling device: [Cyclone Team], [Cyclone Bootloader]
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia Application v01.42, (Jul 5 2010 20:38:02, gcc v4.3.2, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2010 wk23
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C000292C
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk32
Initializing security card...
Card Serial Number: D70000A0
Card Firmware Revision: 0109
Card is activated
Box is activated
Super DCT4 Activation: FALSE
Initializing FBUS...
All initialized - Ready to work
Scanning avaiable products...
Processing C:\Program Files\Nokia\Phoenix\Products\...
Found 29 products, Filtering BB5 Products - wait...
3 Products left after filtering. Ready.
Retrieving Variants for Product RM-115 - wait...
2 Variants Retrieved
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11500112EE450052D8FDF4FCAEE246B11936E106
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.6.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x0001002F00006921, AMD, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x0001002F (AMD), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.6.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A8192FC6AD7BF7A1A4419A3953F3856B1F3F7D4A
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
CMT CCC Not Found
CMT HWC Not Found
Storing VARIANT...
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Backing up simlock...
Simlock backup problem -> Phone not detected
Backup simlock thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm115__06.60.mcusw (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11500112EE450052D8FDF4FCAEE246B11936E106
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm115__06.60.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.6.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x0001002F00006921, AMD, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x0001002F (AMD), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.6.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A8192FC6AD7BF7A1A4419A3953F3856B1F3F7D4A
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x000006BF, NOR
EraseArea[0,CMT]: 0x000006C0-0x0001FFFF, NOR
EraseArea[0,CMT]: 0x00020000-0x0007FFFF, NOR
EraseArea[0,CMT]: 0x00080000-0x000DFFFF, NOR
EraseArea[0,CMT]: 0x00100000-0x001FFFFF, NOR
EraseArea[0,CMT]: 0x00200000-0x002DFFFF, NOR
EraseArea[0,CMT]: 0x002E0000-0x00EDFFFF, NOR
EraseArea[0,CMT]: 0x00EE0000-0x00EF7FFF, NOR
EraseArea[0,CMT]: 0x00EF8000-0x00EFFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 68.875s
Writing all blocks...
Writing CMT NOLO Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT UPDAPP Certificate...
Writing CMT DSP0 Certificate...
Writing CMT MCUSW Certificate...
Writing CMT PMM_CONF Certificate...
Writing CMT SBIF_CONF Certificate...
Programming Status OK!
All blocks written OK! Time taken 63.562s
Flashing Speed: 1715,36 kBit/S
Restarting MCU...
Processing rm115__06.60.mcusw (APE)...
Processing rm115__06.60.ppm_i (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11500112EE450052D8FDF4FCAEE246B11936E106
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm115__06.60.ppm_i, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.6.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x0001002F00006921, AMD, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x0001002F (AMD), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.6.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A8192FC6AD7BF7A1A4419A3953F3856B1F3F7D4A
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x00F00000-0x0145FFFF, NOR
Waiting 320s for erasure finish...
Erase taken 21.781s
Writing all blocks...
Programming Status OK!
All blocks written OK! Time taken 19.562s
Flashing Speed: 1751,26 kBit/S
Restarting MCU...
Processing rm115__06.60.ppm_i (APE)...
Processing rm115__06.60.image_ctv_ua (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11500112EE450052D8FDF4FCAEE246B11936E106
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
rm115__06.60.image_ctv_ua, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.6.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x0001002F00006921, AMD, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x0001002F (AMD), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.6.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A8192FC6AD7BF7A1A4419A3953F3856B1F3F7D4A
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x01460000-0x01FDFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 64.594s
Writing all blocks...
Programming Status OK!
All blocks written OK! Time taken 23.203s
Flashing Speed: 1787,19 kBit/S
Restarting MCU...
Processing rm115__06.60.image_ctv_ua (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version V 06.60
MCU Date 30-07-07
Product RM-115
Manufacturer (c) Nokia.
IMEI 356432010089659
Mastercode 4033575167
IMEI Spare 3A65340201806905
IMEI SV 3365340201806905F8000000
PPM V 06.60, 30-07-07, RM-115, (c) Nokia. , I
PSN FC0650970
Product Code 0535003
Module Code 0202802
Basic Product Code 0526256
PSD 0000001D00000000
RETU 32
TAHVO 53
AHNE 11
HW 1018
RFIC 17211721
DSP dsp_mojito_05w46v50.1
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
Phone is in Power Off Mode
Power Off mode set
Normal mode set
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006010C192101001101
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11500112EE450052D8FDF4FCAEE246B11936E106
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
CMT_BOOT_ROM_CRC: 191EC665
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.6.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
FlashChip[0,CMT]: 0x0001002F00006921, AMD, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x0001002F (AMD), Size: 32MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.6.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A8192FC6AD7BF7A1A4419A3953F3856B1F3F7D4A
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
Started Phone Security Analysis...
MCU Version V 06.60
MCU Date 30-07-07
Product RM-115
Manufacturer (c) Nokia.
IMEI 356432010089659
Mastercode 4033575167
Reading Security Block...
Security block OK and saved to "RM-115_356432010089659_07.07.2010_180535.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"11500112EE450052D8FDF4FCAEE246B11936E106.C000292C" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
SIMLOCK FOUND AND CHECKSUM OK! PASSED!
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!

[socrates]

Аппарат открывал??? Обрати внимание на пины правее конектор шлейфа, часто вода, не спеши ушивать!!!

[слайч]

Флешка не битая, так как прошился телефон без ошибок. Проверь последней версией ты прошил его или нет. Если нет, попробуй последней прошить, а потом смотреть плату на наличие окисления.

[Pedro]

Вот это Failed to read info -> Failed to read SP info не смутило? Считай инфо и выложи лог

[ceshurik_L]

100% площадка с контрольными точками, почистить и если не выгнили, то тел стопудово оживет. Только что такой поднял!

Если нет, попробуй последней прошить, а потом смотреть плату на наличие окисления.

вначале смотрят на наличие окислов, а потом уже шьют!

[Эдмин]

проверить шлейф

[PROHOR RU]

100% контрольные площадки в окислах

[слайч]

вначале смотрят на наличие окислов, а потом уже шьют!

Так если он его уже прошил, не нужно отбрасывать что он прошил прошивкой ниже чем была установлена. Под симптомы тоже подходит...

[orgtech]

Был такой после замены флеш проблема исчезла, походу битая рам во флешке

[VT_Service]

серийники сотри из лога.
А то братья-китайцы нашлепают клонов и твоего цыклона...
з.ы. по делу, дай угадаю, он еще и инфу не считывает.
SX4 пролей PM, затем прошей заново и разблокируй.

[валидол]

На днях точно такой же телефон был не много подлиты тестовые площадки были возле разъема, вычистил все окислы дефект остался, пришлось варварски срезать скальпелем площадки только так. Скорее всего это ваш случай.

[vlad956]

Сегодня тоже попался с такой неисправностью. Помогло тоже варварское удаление скальпелем трёх крайних контрольных точек, чистка не помогала. Телефон нормально заработал.