Показано с 1 по 5 из 5

Тема: 6120c, ASIC not Supported

  1. #1
    Mega Member
    Регистрация
    23.09.2008
    Адрес
    Красноводск, ТМ
    Сообщений
    1,231
    Спасибо
    578
    Благодарностей: 251 : 159

    6120c, ASIC not Supported

    Попался тут на смену языка 6120с RM-243. Прошито их уже немало было, но с этим что-то непонятное. В теле 7.1 версия, пакет с русс, укр языками, нужно залить euro2 (турецкий), которого для этой версии или не существует или я не смог найти. Хотел сделать понижение (backup, full erase, flash, RPL, PM+SX4). Но насторожил чек UFS:

    Скрытый текст: Показать
    1ST BOOT : C0,07 [Rm-243] [2.1.0.1]
    RAPx ID : 000000010000022600010006400C192101051103
    EM 1 ID : 00000296
    EM 2 ID : 00000B22
    RAPx PBID : 22B000059395005216CB328A669D66FB52D5C910
    RAPx MODE : 00
    RAPx HASH : 479C6DDE3942E12C429C1D6ADED80371
    RAPx ROID : 4B9B75103E691FF8
    CMT 1ST Boot OK
    Boot not Found: ASIC not Supported
    CMT 2ND Bt: ASIC not Supported
    BAD BOOT
    ERR: CMT 2ND Boot


    Это чек Cyclone (вроде все ок):

    Скрытый текст: Показать
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    APE Boot skipped on user request
    Flashbus Write baud set to 5.0Mbits
    Restarting MCU...


    Но при попытке создания RPL from phone:

    Скрытый текст: Показать
    RPL Creation started...
    Processing CMT Part...
    Storing Product Code...
    Storing PSN...
    Storing HWID...
    Trying to store Simlock...
    Reading Configuration Key...
    Hashing...
    Reading SHA1-RSA Signature...
    Reading SHA1-HMAC Signature...
    Storing Simlock...
    WMDRM Store not supported
    Reading Security Block...
    Security block OK and saved to "RM-243_351983048496337_19.07.2010_91454.SecurityBlock.PM"
    WARNING: "22B000059395005216CB328A669D66FB52D5C910.C0002B27" Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Prepare phone failed with message -> Not found required CMT Secondary Loader
    Neither CYC file and exists or failed to read it from phone (Failed to Boot / Prepare Phone)
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    APE Subsystem Not Found
    Flashbus Write baud set to 5.0Mbits
    Storing NPC...
    Storing CCC...
    Storing HWC...
    CMT VARIANT Not Found
    Restarting MCU...
    RPL Saved OK


    Собственно, прошу помощи по след. вопросам:
    1. Что за неподдерживаемый ASIC на 6120с? Что-то новенькое?
    2. Удастся ли стереть и главное залить в него бэкапы? Кто-нибудь пробовал?
    3. Можно ли залить языковой пакет от 7.02 в тел с MCU 7.1?
    Последний раз редактировалось asg-gealt; 19.07.2010 в 18:46.

  2. #2
    Mega Member Аватар для Dym
    Регистрация
    28.04.2007
    Адрес
    Питер,RUS
    Сообщений
    1,543
    Спасибо
    404
    Благодарностей: 237 : 117
    ....хм... никогда UFS на эту модель так не ругался,проверь кабель, поиграйся с галками Dula line , 1331 и One boot, Переустанови сюиту, подкинь папку FLASH с форума с загрузщиками ибо - Boot not Found.Переустанови сюиту.

  3. #3
    Mega Member
    Регистрация
    23.09.2008
    Адрес
    Красноводск, ТМ
    Сообщений
    1,231
    Спасибо
    578
    Благодарностей: 251 : 159
    Кабель исключается - им прошит не один десяток 6120, модель популярная. Прищепкой тоже пробовал. Вот папку флэш можно попробовать подкинуть... Остается, однако, непонятки с циклоном.. Ему-то что не нравится? В общем странное дело.

  4. #4
    Member
    Регистрация
    13.09.2007
    Адрес
    Россия 36
    Сообщений
    475
    Спасибо
    46
    Благодарностей: 126 : 30
    Код:
    Prepare phone failed with message -> Not found required CMT Secondary Loader
    не может найти соответствующий загрузчик - либо неправильно определяет тип флеши, либо действительно проблема с кабелем или сьюиту переустановить.

  5. #5
    Mega Member
    Регистрация
    23.09.2008
    Адрес
    Красноводск, ТМ
    Сообщений
    1,231
    Спасибо
    578
    Благодарностей: 251 : 159
    Никакие пляски не помогли добиться нормального чека. Тел был успешно прошит циклоном с галкой Downgrade:

    Скрытый текст: Показать
    Processing pre flash tasks...
    Backing up RPL...
    RPL Creation started...
    Processing CMT Part...
    Storing Product Code...
    Storing PSN...
    Storing HWID...
    Trying to store Simlock...
    Reading Configuration Key...
    Hashing...
    Reading SHA1-RSA Signature...
    Reading SHA1-HMAC Signature...
    Storing Simlock...
    WMDRM Store not supported
    Reading Security Block...
    Security block OK and saved to "RM-243_351983048496337_20.07.2010_110324.SecurityBlock.PM"
    WARNING: "22B000059395005216CB328A669D66FB52D5C910.C0002B27" Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Prepare phone failed with message -> Not found required CMT Secondary Loader
    Neither CYC file and exists or failed to read it from phone (Failed to Boot / Prepare Phone)
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    APE Subsystem Not Found
    Flashbus Write baud set to 5.0Mbits
    Storing NPC...
    Storing CCC...
    Storing HWC...
    CMT VARIANT Not Found
    Restarting MCU...
    RPL Saved OK
    RPL backup thread finished, continuing...
    Backing up simlock...
    MCU Version V 07.10
    MCU Date 15-07-09
    Product RM-243
    Manufacturer (c) Nokia
    IMEI 351983048496337
    Mastercode 251033613
    Simlock backup OK, saved to RM-243_351983048496337_20.07.2010_110335.SLBackup.PM
    Backup simlock thread finished, continuing...
    Applying downgrade patch...
    Downgrade patch OK!
    Pre flash tasks finished, continuing...
    Processing rm243_07.02_prd_core.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    rm243_07.02_prd_core.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    Flashbus Write baud set to 5.0Mbits
    Sending Certificates...
    Certificates OK
    Partitioning...
    Partitioning OK
    Started group flash erase
    EraseArea[0,CMT]: 0x00040000-0x00082FFF, ONENAND
    EraseArea[0,CMT]: 0x00083400-0x0087FFFF, ONENAND
    EraseArea[0,CMT]: 0x00B80000-0x04DFFFFF, ONENAND
    Erase Partition (CMT)
    Waiting 320s for erasure finish...
    Erase taken 0.469s
    Writing all blocks...
    Writing CMT ADA Certificate...
    Writing CMT KEYS Certificate...
    Writing CMT PRIMAPP Certificate...
    Writing CMT RAP3NAND Certificate...
    Writing CMT PASUBTOC Certificate...
    Writing CMT PAPUBKEYS Certificate...
    Writing CMT SOS*UPDAPP Certificate...
    Writing CMT SOS*DSP0 Certificate...
    Writing CMT SOS*ISASW Certificate...
    Writing CMT SOS*CORE Certificate...
    Writing CMT SOS+ROFS Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 50.125s
    Flashing Speed: 7302,34 kBit/S
    Restarting MCU...
    Processing rm243_07.02_prd_core.fpsx (APE)...
    Processing rm243_ENO_A_2009wk15v0.100.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    rm243_ENO_A_2009wk15v0.100.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x00880000-0x00B7FFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.31s
    Writing all blocks...
    Writing CMT SOS*ENO Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 1.750s
    Flashing Speed: 6740,01 kBit/S
    Restarting MCU...
    Processing rm243_ENO_A_2009wk15v0.100.fpsx (APE)...
    Processing rm243_07.02_prd_vB02_01_euro2.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    rm243_07.02_prd_vB02_01_euro2.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x03300000-0x04DFFFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.172s
    Writing all blocks...
    Writing CMT SOS+ROFX Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 27.78s
    Flashing Speed: 6968,99 kBit/S
    Restarting MCU...
    Processing rm243_07.02_prd_vB02_01_euro2.fpsx (APE)...
    Processing rm243_07.02_prd_UDA_Nokia_Noir.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 22B000059395005216CB328A669D66FB52D5C910
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    rm243_07.02_prd_UDA_Nokia_Noir.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.20.1, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x04E00000-0x07B3FFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.250s
    Writing all blocks...
    Programming Status OK!
    All blocks written OK! Time taken 0.625s
    Flashing Speed: 1459,08 kBit/S
    Restarting MCU...
    Processing rm243_07.02_prd_UDA_Nokia_Noir.fpsx (APE)...
    All images processed OK! Processing post flash tasks...
    Setting Factory Defaults...
    Factory defaults OK
    Reading info...
    MCU Version V 07.02
    MCU Date 18-05-09
    Product RM-243
    Manufacturer (c) Nokia
    IMEI 351983048496337
    Mastercode 251033613
    IMEI Spare 3A15890384943603
    IMEI SV 3315890384943653F7000000
    PSN MBM553137
    Product Code 0552780
    Basic Product Code 0539292
    PSD 0000000000000000
    LPSN 0
    RETU 16
    TAHVO 22
    AHNE 11
    HW 1102
    RFIC 17141716
    DSP 06w41pb_08w28.0.1_rm243
    Simlock Server SIMLOCK SERVER
    Simlock Key 2440700000000000
    Simlock Profile 0000000000000000
    Simlock Key Cnt 0
    Simlock FBUS Cnt 0
    Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [1,2] State: OPENED Type: GID Data: FFFF
    Simlock [1,3] State: OPENED Type: GID Data: FFFF
    Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [2,2] State: OPENED Type: GID Data: FFFF
    Simlock [2,3] State: OPENED Type: GID Data: FFFF
    Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [3,2] State: OPENED Type: GID Data: FFFF
    Simlock [3,3] State: OPENED Type: GID Data: FFFF
    Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [4,2] State: OPENED Type: GID Data: FFFF
    Simlock [4,3] State: OPENED Type: GID Data: FFFF
    Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [5,2] State: OPENED Type: GID Data: FFFF
    Simlock [5,3] State: OPENED Type: GID Data: FFFF
    Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [6,2] State: OPENED Type: GID Data: FFFF
    Simlock [6,3] State: OPENED Type: GID Data: FFFF
    Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF
    Simlock [7,2] State: OPENED Type: GID Data: FFFF
    Simlock [7,3] State: OPENED Type: GID Data: FFFF
    Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
    Read info thread finished, continuing...
    Post flash tasks finished!
    Flashing successfully finished!

Похожие темы

  1. 5530 - ASIC not Supported
    от Справедливый в разделе Телефоны BB5
    Ответов: 2
    Последний ответ: 16.02.2011, 18:24
  2. 1101 IMEI: ??????-??-??????-?, ASIC: 2
    от ADUCK в разделе Nokia для новичков
    Ответов: 9
    Последний ответ: 05.04.2007, 12:34
  3. Вопрос про ASIC.
    от Radiotrance в разделе Nokia аппаратный ремонт
    Ответов: 8
    Последний ответ: 03.03.2007, 18:59
  4. 6070 asic
    от master_halid в разделе Nokia для новичков
    Ответов: 11
    Последний ответ: 25.01.2007, 23:27
  5. ASIC 7
    от 04031974 в разделе Телефоны DCT4/WD2/TIKU
    Ответов: 2
    Последний ответ: 17.10.2005, 19:12

Социальные закладки

Социальные закладки

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •  
  Рейтинг@Mail.ru