audiovox 4000

[Igoros2001]

Может кто подскажет распайку кабеля под audiovox 4000,
а то валяется без дела. Хотябы RX, TX

[100rozh]

Igoros2001 стукнись в аську 53499671.

[Vimas]

скажи куда - скину распиновку
а кто знает как в этом звере каналы или прл прописать?

[Igoros2001]

Audiovox CDM-4000 XL Cellular Phone (BAM)
NAM Programming

The NAM (Number Assignment Module) contains information about the unit's
telephone number, related class of service, and optional programmable
features. Certain information must be programmed into the unit from the
keypad before the unit is ready for operation. In using these instructions
refer to the Menu Structure below.

To enter the NAM Programming menu press [2][8][9][F >][#][1] after green
light goes out. The phone will display:

NAM1
Setting?
Yes >

To program NAM1 press [F >] (refer to NAM1 & NAM2 Programming Menu
below) or press [\/] for programming NAM2. The phone will display:

NAM2
Setting?
Yes >

To program NAM2 press [F >] (refer to NAM1 & NAM2 Programming Menu
below) or press [\/] for General Setting. The phone will display:

General
Setting?
Yes >

To set the General Settings refer to "General Settings Menu" below.

Note: When the phone is shipped from the manufacturer, the setting for
EVRC is disabled. To enable EVRC, or toggle EVRC enable and EVRC
disable, please press [#][7][6][3][*][F][F].

NAM1 & NAM2 Programming Menu

A. Simple NAM1 or NAM2 Programming

1. Enter the mobile's phone number including the area code. Press [\/].

NAM1 Common
Phone Number
xxx-xxx-xxxx

2. Enter the Home SID. Press [\/].

NAM1 Common
Home SID
xxxxx

3. Press [>] to save your settings and exit the NAM1 or NAM2 Simple
Programming. The phone sill display:

Please Wait
NAM
Writing!

B. Extensive NAM1 or NAM2 Programming

The following section displays the flow chart of the complete NAM
Programming menu. Please note the following:

1. You can exit the main menu and save your settings from any part of the
menu. To do this you must first press [\/] to scroll to the next item,
and then press [phone symbol] (Send). ^1

2. To scroll up please press [/\]. toi scroll down or go the next item
of the NAM Programming menu, please press [\/].

3. To choose "YES" in a decision item please press [>].

4. Preferred or affiliated SIDs can be programmed in the E/R List Menu.
Up to 200 SIDs can be entered in the E/R. to enter an Affiliated or
Preferred SID press [>] and enter the SID number. To enter another
SID press [\/}.

^1 In order for the last entry to be saved you must scroll down to the
next item before exiting the NAM Programming Menu.

Extensive Programming Flow Chart

(A)
|
\/
NAM1 or NAM2
Common Phone
Number
|
\/
Home SID
|
\/
Simple NAM? --------> SAVE SETTINGS AND
| EXIT NAM
| PROGRAMMING
\/
CDMA Setting? -----> MCC ------> IMSI_S ------> IMSI 11_12
| |
| \/
| CDMA Home SID
| |
| \/
| CDMA Home NID
| |
| \/
| MOB_TERM_HOME
| |
| \/
|<-- MOB_TERM_FOR_NID <------------------ MOB_TERM_FOR_SID
|
\/
AMPS Setting? ---------> Phone Number ----------> Home SID
| |
| \/
|<----------------- Paging Channel <----------- EX
|
\/
ER List Setting? --------> REFER TO NOTE 4 ABOVE
|
\/
Common Setting? ---------> Display Tel. Number ----> A-Key
| |
| \/
|<-------------------------------------------- ACCOLC
|
\/
NAM2 Setting

General Setting Programming Menu

General Setting
|
\/
ROAM Ind. Status (See below)
|
\/
Idle Banner Setting ----------------> Enter ALPHA
| |
| \/
|<-----------------------------------
\/
Wakeup Logo
|
\/
Restriction Recall ------------------------> Slot Cycle Index
Range |
|
\/
Prog. Code <-------------------------------- Station Class Mark
|
|
\/
Activation Code ----------------------------> Protocol Rev.
Number
|
|
\/
Model Number <------------------------------- Firmware Rev.
| Number
|
\/
ESN (Decimal) ------> (A)

Enhanced Roaming

The CDM-4000 is equipped with Enhanced Roaming (ER).

Enhanced Roaming:

ER enables Carriers to pre-program up to 200 SIDs per NAM. When the phone
is operating out of the Home area, the phone will seek and lock onto one
of the pre-programmed SIDs, if available.

ER SID Capacity:

Up to 200 SIDs can be pre-programmed in NAM1. In addition, up to 200 SIDs
can be pre-programmed in NAM2.

ER SID Types:

Two categories of SIDs are available: (A) Affiliated and (B) Preferred.
The 200 (ER) SID slots in NAM1 (and NAM2) can be designated as Affiliated
or Preferred in any combination. The only restriction is that the total
number cannot exceed 200.

ER Operation

The phone has the following A/B switch Selections:
Auto Roam, Prefer, Home Only, Non Prefer, and Standard.

The enhanced Roaming function is active when the A/B selection is in Auto
Roam or Prefer. In Auto Roam, both Affiliated as well as preferred SIDs
can be selected. In Prefer only Affiliated SIDs can be selected. The
other A/B selections are self-explanatory.

SID Preference in ER Mode

The phone will scan for SIDs that are programmed in its ER memory and
select in the following order of preference;

1) Home SID or Affiliated SID in CDMA mode (Auto Roam and Prefer)
2) Home SID or Affiliated SID in Analog mode (Auto Roam and Prefer)
3) Preferred SID in CDMA mode (Auto Roam only)
4) Preferred SID in Analog mode (Auto Roam only)
5) Other SIDs (Auto Roam only)

(Note: In the ER mode, there will be "No Service" if there is not usable
signal from a SID or the ER or a SID on the same side as the Home
System, even if there is a usable signal from the "other side".
Under service would be provided for 911 type calls).

Programming of ER SIDs:

ER SIDs can be programmed by the following methods:

a) By key-pad Entry.
b) Pre-programmed by Audiovox if specified by the Carrier.
c) Via a PC, using special software available through Audiovox.

Roam Indicator

The ROAM Indicator operates as follows:

Phone operating in: ROAM Indicator

Home SID OFF
Affiliated SID Carrier Option (see note below)
Preferred SID ON Steady
Other SID Flashing

ROAM light OFF or ON, in an Affiliated SID area, is a Carrier option.
This is selected via the "ROAM Indicator Status" (programming step 30) as
follows:
ROAM Indicator Status = 0 ROAM Light ON
ROAM Indicator Status = 1 ROAM Light OFF

Key-Pad Entry of ER SIDs (Programming steps 15 & 16)

The example below is for NAM1. the procedure is the same for all other
NAMs.

While in the programming mode for NAM1, use the down arrow (Vol) to scroll
to:
40) "NAM1 ER List Settings?"
41) Select "yes"
42) The next menu will be: "NAM1 ER List Affiliated?"
43) Select "yes" (F)
44) The next menu will be: "NAM1 1/200 Affiliated"
45) Enter the first Affiliated SID number
46) Push (Vol) to scroll to the next available SID slot.
47) The next menu will be: "NAM1 2/200 Affiliated.
48) Enter the next Affiliated SID number.
49) Repeat steps 47 - 49 until all the Affiliated SIDs have been entered

After all the affiliated SIDs have been entered, if there are Preferred
SIDs to be entered follow steps 50 to 60 below. Otherwise, scroll to the
next programming step, or exit programming as required.

50) Press RCL to return to the menu of step 42 ("NAM1 ER List
Affiliated?")
51) Press Vol.
52) The next menu will be: "NAM1 ER List Preferred?"
53) Select "yes" (F)
54) The next menu will be: "NAM1 x+1/200 Affiliated"
(x+1 is the next available SID slot)
55) Push (Vol) to scroll to the next SID slot.
56) The next menu will be: "NAM1 2/200 Affiliated"
57) Enter the next Affiliated SID number.
58) Repeat steps 57 - 59 until all the Affiliated SIDs have been entered
59) After all the Preferred SIDs have been entered, scroll to the next
programming step, or exit programming as required.
Распин если не в облом можно на [email protected]