Griffin и не включающаяся 8910i(+)

[Baza99]

Cитуация:
8910i после попыток удачно прошить КИТАЙЦЕМ
перестала есс-но включатся,нарыл гриффин,кабель
сам сваял,проверил-вроде ок
скачал прошиву,галку на MCU ,выбрал,выбрал яз.пакет
жму флэш,жму на кнопу вкл фона,коротко, ... и вот такая байда,что делаю неверно?
или проблема в кабеле?

[kerpal]

А теперь давайте посмотрим на схему вашего кабеля... ПАПА

[0000D301] Check location of FIA files. Otherwise download and install Griffin Gold
Installer.

[0000D303] Failure to auto power phone. Press flash and wait 2sec then press on/off
on phone very quickly
Set up everything then disconnect power to Griffin and reconnect after 5sec.
Try above again.

[5555FFBC]

[22222222] FIA Files are old. Install newest flash package. Check folder
structure regarding correct c:\program files\ or c:\program\

[21212211] FIA files are old or missing reinstall griffin or update FIA files

[BDBDADAD] MCU and PPM versions are not the same, Verify that you have the latest
FIA-files installed

[78878778] Possibly no corresponding .fia file or flash chip is dead. In Griffin
software versions lower than 1.983 occur while flashing 7650 and 3650 - need to be updated


[78878778] Check the FIA files installation, upgrade to latest and verify that
they are in the correct folder. Erase old ones then install new. Possible flash chip error.

[FFFF9000] No communication with phone.
[FFFF9100] Check the cable and connection to phone and check LPT settings in BIOS, EPP+ECP.
[FFFF9200] Try bending the battery connectors a bit upward. In some connectors they
have difficulties connecting.
[FFFF9300] Possibly Flash IC malfunction.
[44449000]
[44449300]

[FFFF8200]

[FFFF917B]

[FFFFFFC1] When flashing 9210. Maybe is your flash IC is corrupted or you need to
reball the flash ic and try to reflash again.

[FFFFFFD4] While flashing 3650 means that the box isn't updated to use with 3650.
Upload last .gpd file to box.

[FFFFFFBC]

[FFFFFE36] Phone not detected correctly, upgrade Griffin to latest version.

[FFFFB003] Possibly corrupted files in Griffin folder. Reinstall Griffin Gold Installer
[5555B003]


[33333333] Box is not activated
If your supplier is unable to register your box, you must pay 150$ to The Griffin
Team for registration.

[BBAA1B34]

[5555335D]



Flashing 6600:
Flashing 6310i:
Invalid************Upload This is caused by mismatch in directory structure.
Copy product info directory to c:\program files\nokia\phoenix\products\NPL-1 or to
c:\program\nokia\phoenix\products\NPL-1.

Flashing 7650:


DE:3451 Check connection and power

After flashing, do a manual factory reset by pressing *#7370#. It’s always
wise to do a *#7370# before flashing symbian phones.
Make sure the cable have a 3,3kohm resistor in serial from BSI to RJ-45.

Start-up failed on Symbian phones
Format user area.

3650, 7650 4x blink Make sure the cable have a 3,3kohm resistor between BSI and GND.


"Invalid MCU flash file specified"
Make sure the files are in the right directory. Make sure that the files are not read-only.

Extracting content package fail
Make sure PPM and CP file is from same version. Try flashing with MCU and PPM
only then flash with MCU + PPM + CP
If it still fails, try with other version. Make sure files are not read-only.




Do a Full phone formatting on your 6600! as steps below,

1. Make sure you have at least 3/4 charge of battery power left.

2. Backup your contacts list and personal files to MMC memory card.
Also backup sim-rebuild and pmm from phone.

3. Switch-off your 6600 phone.

4. Press and hold 3 keys; Green dial key, * Star key, no. 3 key on
keypad and then press the power on/off to switch on the 6600 phone.

Remember, do not let go the 3 press and hold keys until you see a
formatting word screen show!

5. After a few minutes when the Full phone formatting completed, your
6600 will back to original system and factory setting.

Normal reset *#7780# 3rd party apps remains

Deep Reset *#7370# removes everything

Gammu.dll was not found.
Download gammu.dll from www.griffinteam.net and login with your box’s serial number.
Place file in Griffin program directory.



Is it possible to change IMEI with Griffin?
With DCT-3 you can’t do it with Griffin, use nokiatool, knok, dejan, rolis or any
other software for those phones.
With DCT-4 you must first change UEM IC and then create a .ask file to send to someone
who can make a .rpl from that and upload to phone.
NOTE, changing IMEI is prohibited by law in many countries!

Installation problems when installing latest Phoenix flash files.
Install earlier versions of flash file and install latest again. Some of the flash
files is updates from earlier versions.


How to convert 7250 to 7250i
Make ASK for 7250 repair/conversion, get RPL file, Flash with 7250i MCU/PPM/CP, u
pload ASK and PM values


How to turn a flashed 6610 back to 6610 from 7210?
Make a backup of your .pmm by using the serial menu and after flashing upload it
to the phone again.
If no backup exists, check the .pm file inside the nhl-4u directory and change ….
Then flash ppm again.

Where to get the latest Griffin.exe file?
Official releases of the Griffin.exe software is found at www.griffinteam.net and
login with your box’s serial number.

Where to get the Phoenix flash files from?
Ask your reseller for password to their ftp-server or look around the forums
mentioned above.

[Baza99]

http://www.tele-way.com/productlist/...10_revised.gif