3110 интересный случай

[rifa]

После подтверждения - CS.
Проливка 1и 309 блоков с авторизацией не помогла,

Uploading RF/Battery tune to phone...
Using : RM-237.pm
Operating mode is OK, no need change...

Field 1
   Record 0 write - Ok
   Record 2 write - Ok
   Record 4 write - Ok
   Record 6 write - Ok
   Record 8 write - Ok
   Record 13 write - Ok
   Record 16 write - Ok
   Record 18 write - Ok
   Record 20 write - Ok
   Record 25 write - Ok
   Record 29 write - Ok
   Record 34 write - Ok
Field 309
   Record 0 write - Ok
   Record 1 write - Ok
   Record 2 write - Ok
   Record 4 write - Ok
   Record 5 write - Ok
   Record 7 write - Ok
   Record 8 write - Ok
   Record 17 write - Ok
   Record 22 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED :(
 - > Try different PM files or "Restore CCC/HWC" option

запись CCC/HWC тоже не дала результатов

Will Write CCC/HWC keys now...

Using : RM-237.rpl
CCC Data found!
HWC Data found!

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Preparing for write certificates...

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Done!

Elapsed: 00:00:17

Connect phone on selected interface...

Phone found!
Series 40 Device detected! 
read info...  - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
 - > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

И всё это после ПОЛНОГО стирания ТА...
Стёр
Прошил 7,21
Залил только NPC с бекапа
PM
RPL без NPC с папки ATF
SX4

Reading Phone Info....
Connected phone -    Nokia 3110c
Software ver : V 07.21 05-11-08 RM-237 (c) Nokia.           
IMEI    :      353183032582485
Ape Ver :      
APE Var :      
APE ADSP:      
DSP Ver :      ICPR61_08w10
APE Test:      
PPM     :      V 07.21
05-11-08
RM-237
(c) Nokia.           
I
CNT     :      Content: i_ny
V 07.21
05-11-08
RM-237
(c) Nokia.           

Product SN   :     7F0821634
Product code :     0514950
Base Prd.code:     0542523
Module code  :     0203291
Long Prod.SN :     
Hardware info=======
HWID  : 2000
Retu  : 32
Tahvo : 53
Batery: 4353 mV
Camera: 
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: 
RF ic : 17211721
Lock info ===========
IMEI       : 353183032582485
IMEI spNet : 
IMEI svNet : 

Conf key     : 0000000000000000
Provider key : 2440700000000000
Provider    : AT&T;U.S.A. (3650)
Counters   : Key 0  [3] , Fbus 0  [10]
Blocks      : 7

LOCK STATUS :
=============================
BLK : 1
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS :  All Open
=============================
User Code : 12345
MMC pwd  : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery] 

Done!

Что можно предпринять ещё?

[AQ7]

после стирания Restore CCC/HWC делали?

[rifa]

после стирания Restore CCC/HWC делали?

И всё это после ПОЛНОГО стирания ТА...
Стёр
Прошил 7,21
Залил только NPC с бекапа
PM
RPL без NPC с папки ATF
SX4

Лог полного стирания и прошивки, ничем не примечателен

Full Erase started...
Asic : CMT , Sub : NOR
Erase Area 0x00000000-0x01FFFFFF
Using TimeOut : 10 min ( 600 sec )
Erasing, wait.....
CMT : Erase Ok
Done

Phone disconected!

Connect phone on selected interface...

Read and Check phone data...
BB5 bus checking...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

PrReq : NOR , 00

Init Service mode... Wait...

Init Service Mode Failed, can't proceed checking... :(

Connect phone on selected interface...

Core version : 1.29  Rev : 1.0

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm237__07.21.mcusw
PPM : rm237__07.21.ppm_i
CNT : rm237__07.21.image_i_ny
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected

Backup enabled, Will read Certificates now...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

CMT : Read NPC certificate...
Cert size : 0 byte(s)
CMT : Read CCC certificate...
Cert size : 0 byte(s)
CMT : Read HWC certificate...
Cert size : 0 byte(s)
CMT : Read VARIANT certificate...
Cert size : 0 byte(s)
 - > No any CRT data (MCU damaged/CERT erased), skip saving


Init Service mode... Wait...

Init Service Mode Failed!
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.mcusw
Found 9 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00020000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x000DFFFF
CMT , NOR , Area : 0x00100000 - 0x001FFFFF
CMT , NOR , Area : 0x00200000 - 0x0031FFFF
CMT , NOR , Area : 0x00320000 - 0x0105FFFF
CMT , NOR , Area : 0x01060000 - 0x01067FFF
CMT , NOR , Area : 0x01068000 - 0x0107FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:04
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.mcusw
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [PMM_CONF]
CMT: Writing Hash CERT [SBIF_CONF]
Total writen 942 blocks
TIME : Write time : 00:01:58 

PrReq : NOR , 00

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.ppm_i
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01080000 - 0x0151FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.ppm_i
Total writen 211 blocks
TIME : Write time : 00:00:25 

PrReq : NOR , 00

CNT : Converted to 128k page data exist
Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.image_i_ny_128
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01520000 - 0x01FDFFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:02
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.image_i_ny_128
Total writen 200 blocks
TIME : Write time : 00:00:24 

PrReq : NOR , 00


Init Service mode... Wait...

Reading Phone Info....
Connected phone -   Nokia 3110c
Software Info:     V 07.21
05-11-08
RM-237
(c) Nokia.           
IMEI:  12345610654321?
Product code:  0514950
Checking...
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Checking User Certificates...
Total - 0 certs
Uploading certificates...
Writen 21 certs!
AfterFlash operations done ;D
Connect phone on selected interface...

[yoga]

Лог полного стирания и прошивки, ничем не примечателен

Full Erase started...
Asic : CMT , Sub : NOR
Erase Area 0x00000000-0x01FFFFFF
Using TimeOut : 10 min ( 600 sec )
Erasing, wait.....
CMT : Erase Ok
Done

Phone disconected!

Connect phone on selected interface...

Read and Check phone data...
BB5 bus checking...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

PrReq : NOR , 00

Init Service mode... Wait...

Init Service Mode Failed, can't proceed checking... :(

Connect phone on selected interface...

Core version : 1.29  Rev : 1.0

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm237__07.21.mcusw
PPM : rm237__07.21.ppm_i
CNT : rm237__07.21.image_i_ny
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected

Backup enabled, Will read Certificates now...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

CMT : Read NPC certificate...
Cert size : 0 byte(s)
CMT : Read CCC certificate...
Cert size : 0 byte(s)
CMT : Read HWC certificate...
Cert size : 0 byte(s)
CMT : Read VARIANT certificate...
Cert size : 0 byte(s)
 - > No any CRT data (MCU damaged/CERT erased), skip saving


Init Service mode... Wait...

Init Service Mode Failed!
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.mcusw
Found 9 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00020000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x000DFFFF
CMT , NOR , Area : 0x00100000 - 0x001FFFFF
CMT , NOR , Area : 0x00200000 - 0x0031FFFF
CMT , NOR , Area : 0x00320000 - 0x0105FFFF
CMT , NOR , Area : 0x01060000 - 0x01067FFF
CMT , NOR , Area : 0x01068000 - 0x0107FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:04
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.mcusw
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [PMM_CONF]
CMT: Writing Hash CERT [SBIF_CONF]
Total writen 942 blocks
TIME : Write time : 00:01:58 

PrReq : NOR , 00

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.ppm_i
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01080000 - 0x0151FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.ppm_i
Total writen 211 blocks
TIME : Write time : 00:00:25 

PrReq : NOR , 00

CNT : Converted to 128k page data exist
Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.image_i_ny_128
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01520000 - 0x01FDFFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:02
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.image_i_ny_128
Total writen 200 blocks
TIME : Write time : 00:00:24 

PrReq : NOR , 00


Init Service mode... Wait...

Reading Phone Info....
Connected phone -   Nokia 3110c
Software Info:     V 07.21
05-11-08
RM-237
(c) Nokia.           
IMEI:  12345610654321?
Product code:  0514950
Checking...
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Checking User Certificates...
Total - 0 certs
Uploading certificates...
Writen 21 certs!
AfterFlash operations done ;D
Connect phone on selected interface...

Он без ошибок включается с дефолтным имеим? Сразу после стирания и записи SW

[uo5oq]

После подтверждения - CS.
Проливка 1и 309 блоков с авторизацией не помогла,
...
Что можно предпринять ещё?

В MX-KEY нажать кнопку "Recovery certificate" или "Restore cert", как-то так она называется.

[AQ7]

после стирания Security status : Security Damaged!!!!! это не нормально, имхо железо

[uo5oq]

после стирания Security status : Security Damaged!!!!! это не нормально, имхо железо

Не указано, что лог после стирания и записи ТОЛЬКО SW.

[rifa]

Он без ошибок включается с дефолтным имеим? Сразу после стирания

Сразу после стирания ТА не включится, имелось ввиду после записи ПО? Ща проверю
Да, после флешинга с дефолтным именем - после подтверждения CS.

В MX-KEY нажать кнопку "Recovery certificate" или "Restore cert", как-то так она называется.

MXBox а нет в данный момент, Cyclon тоже не поднял тело. Всю жизнь думал что MXBOX восстанавливает только CCC и HWC по данной кнопке.
Вот мужики, давай сначала - суббота - котелок уже совсем не варит -
Стирание

User ACCEPTED FULL ERASE
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Full Erase started...
Asic : CMT , Sub : NOR
Erase Area 0x00000000-0x01FFFFFF
Using TimeOut : 10 min ( 600 sec )
Erasing, wait.....
CMT : Erase Ok
Done

Phone disconected!

Флешинг

Core version : 1.29  Rev : 1.0

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm237__07.21.mcusw
PPM : rm237__07.21.ppm_i
CNT : rm237__07.21.image_i_ny_128
Check FlashFiles, Please, wait...
-> SWversion check skipped : Dead mode selected

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.mcusw
Found 9 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x000006BF
CMT , NOR , Area : 0x000006C0 - 0x0001FFFF
CMT , NOR , Area : 0x00020000 - 0x0007FFFF
CMT , NOR , Area : 0x00080000 - 0x000DFFFF
CMT , NOR , Area : 0x00100000 - 0x001FFFFF
CMT , NOR , Area : 0x00200000 - 0x0031FFFF
CMT , NOR , Area : 0x00320000 - 0x0105FFFF
CMT , NOR , Area : 0x01060000 - 0x01067FFF
CMT , NOR , Area : 0x01068000 - 0x0107FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:04
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.mcusw
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [PMM_CONF]
CMT: Writing Hash CERT [SBIF_CONF]
Total writen 942 blocks
TIME : Write time : 00:01:57 

PrReq : NOR , 00

Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.ppm_i
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01080000 - 0x0151FFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.ppm_i
Total writen 211 blocks
TIME : Write time : 00:00:25 

PrReq : NOR , 00

ConvertImage: Processing rm237__07.21.image_i_ny_128
ConvertImage: Page Size is 128K, no need convert
Transmission mode :  Dual (Ddr, TX2) 
Erase : Processing rm237__07.21.image_i_ny_128
Found 1 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x01520000 - 0x01FDFFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
TIME : Erase time : 00:00:02
PrReq : NOR , 00
Transmission mode :  Dual (Ddr, TX2) 
Write : Processing rm237__07.21.image_i_ny_128
Total writen 200 blocks
TIME : Write time : 00:00:24 

PrReq : NOR , 00


Init Service mode... Wait...

Afterflash not selected, skip
Connect phone on selected interface...

Connect phone on selected interface...

Phone found!
Series 40 Device detected! 
read info...  - Ok

Reading Phone Info....
Connected phone -    Nokia 3110c
Software ver : V 07.21 05-11-08 RM-237 (c) Nokia.           
IMEI    :      12345610654321?
Ape Ver :      
APE Var :      
APE ADSP:      
DSP Ver :      ICPR61_08w10
APE Test:      
PPM     :      V 07.21
05-11-08
RM-237
(c) Nokia.           
I
CNT     :      Content: i_ny
V 07.21
05-11-08
RM-237
(c) Nokia.           

Product SN   :     
Product code :     
Base Prd.code:     
Module code  :     
Long Prod.SN :     
Hardware info=======
HWID  : 
Retu  : 32
Tahvo : 53
Batery: 4370 mV
Camera: 
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: 
RF ic : 17211721
Lock info ===========
IMEI       : 12345610654321?
IMEI spNet : 
IMEI svNet : 

Unable to read Lock table... :(
User code : Crypted
MMC pwd  : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery] 

Done!

Phone disconected!

Connect phone on selected interface...

Или флеша не трётся правильно или AQ7 прав

[yoga]

Сразу после стирания ТА не включится, имелось ввиду после записи ПО? Ща проверю
Да, после флешинга с дефолтным именем - после подтверждения CS.

Проблема все таки железного характера

MXBox а нет в данный момент, Cyclon тоже не поднял тело. Всю жизнь думал что MXBOX восстанавливает только CCC и HWC по данной кнопке.

+ variant_data, если он должен быть в аппарате

[nuakakisho]

tahvo c retu подкинь.

[rifa]

Хмм, отлежалось тело часик, решил вернуть (принималось как на ПО), влил свой бэкап - и вуаля!

Read and Check phone data...
BB5 bus checking...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

PrReq : NOR , 00

Init Service mode... Wait...


IMEI Validation : IMEI Damaged!!!!
- > SIMLOCK , SECURITY Info can be wrong!
- > Need restore NPC backup or RPL


SDD Key status : SDData Damaged!!!!! :(
 - > Do REPAIR SDD , Local SX4 if needed 

SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL phone detected


Done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected! 
read info...  - Ok


Init Service mode... Wait...

Phone disconected!

Connect phone on selected interface...

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
WMDRM key found!
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info : 
CMT ASICID   : 000000010000022600010006010C192101001101
CMT EM0 ID  : 00000232
CMT EM1 ID  : 00000353
CMT PUB ID  : 17300214638F7E56FEC63BA2174FFF9B22B87AC3
CMT MODE ID : 00
CMT R_HASH  : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID  : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg  ,  Rev : 0.0  Ver : 10.42.0 
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT   : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg  ,  Rev : 0.0  Ver : 1.33.1 
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode :  Dual (Ddr, TX2) 

Boot Done!

Preparing for write certificates...

Switching to CMT... 

CMT : NPC erase Ok
Writing NPC... Ok

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Init Service mode... Wait...

Check phone mode...
Phone already in Test mode, skip change...


SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok

Там уже дело дело техники.
Интересный случай...

[pundev1]

3110 ,3109,6300 часто лечилось перекаткой(99процентов и порезкой)проца.
и еще вопрос только у меня именно 3110 по фбасу только делают вид что шьются?а в реале нет?только по юсб нормально шьются.