6700s - только заставка Nokia

[pro-s]

Требуется помощь - непонятная проблема. 6700s при включении только заставка Nokia, при этом на кнопки реагирует, т.е. нажал на кнопки - заставка появилась (с подсветкой). При этом тело шьется и все сбросы проходят.

Изначально принесли не включающимся - потребление 50 mA и все. Чек не проходил (BEST зависал, MX-key выдавал ошибку), в локал не входил. Разобрал и вычистил в районе разъемов немного грязи - ни чего не изменилось. Отпаял батарейку CMOS - чек прошел нормально и тело прошилось последней версией SW, но при включении история описанная выше.

Лог BEST (изначальный)

Booting phone...

BOOT 1ST   : C0

CMT part info : 
CMT ASICID   : 000000030000022600010007600C192102011104
CMT EM0 ID  : 00000C35
CMT EM1 ID  : 00000C30
CMT PUB ID  : 01500104257B0E49144795D0BF229F255E21C042
CMT MODE ID : 00
CMT R_HASH  : 25B977A055BE9B5DEC0C38A2A279C695
CMT ROM ID  : 3E273BF637BE26FA

 - > Change Protocol : NEW

Using NEW Flashing Protocol

CMT : Sending 2nd loader...
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 9.48.0 
CMT Loader sent, Boot Ok
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine

Sending Algo...
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 9.48.0 
FUR_CMT (CMT current) Error!
Erros Set VPP!
PapubKeysReq : Blank (MCU erased or HW error)
Boot done!

Лог MX-key (изначальный)

MXKEY [MxKey Team HTI PLUS Flasher Interface 4], SN: 
Using device: HTI, FW ver: 00.50, SN: 
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0 
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
CMT Data :
SYSTEM ASIC ID: 000000030000022600010007600C192102011104 [RAPUYAMA ver: 1.1]
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 01500104257B0E49144795D0BF229F255E21C042
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
 SecondaryBoot: RAPUv11_2nd.fg [BB5]  version: 12.14.0 revision: 3.0 size: 0x3B40
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000  - 0000 0000  type: RAM, asic:CMT 
Storage1: FFFF 0000  - 0000 0000  type: MMC, asic:CMT 
Storage2: 0000 0000  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage3: 0000 0001  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
 Algorithm: RAPUv11_XSR17_alg.fg [XSR 1.6]  version: 12.14.0 revision: 3.0 size: 0xD4569
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS is blank/erased.

Лог BEST (после отпайки батарейки CMOS)

Read and Check phone data...
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST   : C0

CMT part info : 
CMT ASICID   : 000000030000022600010007600C192102011104
CMT EM0 ID  : 00000C35
CMT EM1 ID  : 00000C30
CMT PUB ID  : 01500104257B0E49144795D0BF229F255E21C042
CMT MODE ID : 00
CMT R_HASH  : 25B977A055BE9B5DEC0C38A2A279C695
CMT ROM ID  : 3E273BF637BE26FA

 - > Change Protocol : NEW

Using NEW Flashing Protocol

CMT : Sending 2nd loader...
Use RAPUv11_2nd.fg  ,  Rev : 3.0  Ver : 9.48.0 
CMT Loader sent, Boot Ok
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
CMT Flash ID : 004000EC < SAMSUNG [SEC] => KAT00F00RA [NAND]
FLIC : 004000EC , NAND , CMT

Sending Algo...
Use RAPUv11_XSR17_alg.fg  ,  Rev : 3.0  Ver : 9.48.0 
Finalize done, Algo sent!
Trans Req : 32 bit, DualLine, Set : 32 bit, DualLine
PapubKeysReq : B1302F79239A2431E816565B36374B1F676A23ACFE
Boot done!


Switch jaf to FBUS...
FbusMode set Ok

SDD Key status : SDData is Ok
CMLA Key status : CMLA key is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected ,  SP_CODE_LEN : 15 


Done!

Connect phone on selected interface...

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

Reading Phone Info....
Connected phone -    Nokia 6700s
Software ver : V ICPR82_11w16.3 19-05-11 RM-576 (c) Nokia
IMEI    :      353390046555445
Ape Ver :      071.004
APE Var :      071.004071.004.05.01071.004.C00.01
APE ADSP:      256
DSP Ver :     ICPR82_11w16
APE Test:      0.049
PPM     :      
CNT     :      
Product SN   :     KDT921233
Product code :     0589660
Base Prd.code:     0580659
Module code  :     0204314
Long Prod.SN :     0
Hardware info=======
HWID  : 2001
Retu  : 35
Tahvo : 00
Batery: 4790 mV
APE HW: 256
RF ic : |Vapaus_5.1 | Aura_?.?
Lock info ===========
IMEI       : 353390046555445
IMEI spNet : 
IMEI svNet : 

Conf key     : 0000000000000000
Provider key : 2440700000000000
Country      : Finland
Operator     : NOKIA (Open)
Counters     : Key 0  [3] , Fbus 0  [10]
Blocks       : 7

LOCK STATUS :
=============================
BLK : 1
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS :  All Open
=============================
User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method 

Done!

Лог MX-key (после отпайки батарейки CMOS)
Version from phone: 071.004
Version from file: 071.004
MXKEY [MxKey Team HTI PLUS Flasher Interface 4], SN: 
Using device: HTI, FW ver: 00.50, SN: 
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0 
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Reading RPL backup ...
Reading Phone IDs ...
CMT Data :
SYSTEM ASIC ID: 000000030000022600010007600C192102011104 [RAPUYAMA ver: 1.1]
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 01500104257B0E49144795D0BF229F255E21C042
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
 SecondaryBoot: RAPUv11_2nd.fg [BB5]  version: 11.34.0 revision: 3.0 size: 0x3B40
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000  - 0000 0000  type: RAM, asic:CMT 
Storage1: FFFF 0000  - 0000 0000  type: MMC, asic:CMT 
Storage2: 0000 0000  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage3: 0000 0001  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage4: 00EC 0040  - 0000 0231 [Samsung 2Gb DDP OneNAND,2 Gbits] type: FLASH,MuxOneNAND, asic:CMT 
Suggested algorithm: XSR 1.6
 Algorithm: RAPUv11_XSR17_alg.fg [XSR 1.6]  version: 11.34.0 revision: 3.0 size: 0xD4029
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: B1302F79239A2431E816565B36374B1F676A23AC
PUBLIC ID: 01500104257B0E49144795D0BF229F255E21C042
PRIVATE ID: 2C239E82C015092781B79B981F9AF5D3FE4D1828
 E-FUSE: 4E3CFBA6
 SEC ROM CRC: 37BE26FA
productData saved.
 
Restarting phone ...
Reading Secure Storage ...
Reading Important data ...
Reading SIMLOCK data ...
Reading CERT data ...
CMT Data :
SYSTEM ASIC ID: 000000030000022600010007600C192102011104 [RAPUYAMA ver: 1.1]
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 01500104257B0E49144795D0BF229F255E21C042
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
 SecondaryBoot: RAPUv11_2nd.fg [BB5]  version: 12.14.0 revision: 3.0 size: 0x3B40
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000  - 0000 0000  type: RAM, asic:CMT 
Storage1: FFFF 0000  - 0000 0000  type: MMC, asic:CMT 
Storage2: 0000 0000  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage3: 0000 0001  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage4: 00EC 0040  - 0000 0231 [Samsung 2Gb DDP OneNAND,2 Gbits] type: FLASH,MuxOneNAND, asic:CMT 
Suggested algorithm: XSR 1.6
 Algorithm: RAPUv11_XSR17_alg.fg [XSR 1.6]  version: 12.14.0 revision: 3.0 size: 0xD4569
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: B1302F79239A2431E816565B36374B1F676A23AC
Reading CMT NPC (0x168 bytes).
Reading CMT VARIANT (0x0 bytes).
Reading CMT CCC (0x160 bytes).
Reading CMT HWC (0xD4 bytes).
Reading CMT R&D (0x0 bytes).
Reading CMT MDM_KEYS (0x0 bytes).
Reading CMT PARTNERC (0x0 bytes).
Flash Imei: 35339004655544
NPC_DATA saved OK
CCC_DATA saved OK
HWC_DATA saved OK
SIMLOCK_DATA saved OK
SIMLOCK_KEY_DATA saved OK
SUPERDONGLE_KEY_DATA saved OK
CMLA_KEY_DATA saved OK
WMDRM_PD_DATA saved OK
RF_DATA saved OK
WARRANTY_DATA saved OK
PROD_DATA saved OK
BT_DATA saved OK
LOCK_DATA saved OK
LOCK120_DATA saved OK
BB_DATA saved OK
RPL saved to "D:\GSM-soft\MX-Key (HTI)\data\backup\BB5_35339004655544_BACK.rpl" 
CMT Data :
SYSTEM ASIC ID: 000000030000022600010007600C192102011104 [RAPUYAMA ver: 1.1]
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 01500104257B0E49144795D0BF229F255E21C042
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
 SecondaryBoot: RAPUv11_2nd.fg [BB5]  version: 12.14.0 revision: 3.0 size: 0x3B40
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000  - 0000 0000  type: RAM, asic:CMT 
Storage1: FFFF 0000  - 0000 0000  type: MMC, asic:CMT 
Storage2: 0000 0000  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage3: 0000 0001  - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT 
Storage4: 00EC 0040  - 0000 0231 [Samsung 2Gb DDP OneNAND,2 Gbits] type: FLASH,MuxOneNAND, asic:CMT 
Suggested algorithm: XSR 1.6
 Algorithm: RAPUv11_XSR17_alg.fg [XSR 1.6]  version: 12.14.0 revision: 3.0 size: 0xD4569
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 6003192102031104, 600C192102031104
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: B1302F79239A2431E816565B36374B1F676A23AC
Processing MCU file: rm576_071.004_prd.core.fpsx 
 [BB5,XSR 1.6]  size: 88.43 MB
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 600C192102031104, 6003192102031104
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Partitioning ...OK
Erase size: 177.06 MB
CMT FLASH,MuxOneNAND area [00020000-0003FFFF]
CMT FLASH,MuxOneNAND area [00060000-004DFFFF]
CMT FLASH,MuxOneNAND area [008E0000-0B53FFFF]
Formating partition ...
Prog.status for Asic CMT ...
 NAND: OK
Flash programming ...
CMT ADA block sent
CMT KEYS block sent
CMT PRIMAPP block sent
CMT RAP3NAND block sent
CMT SOS+PMML block sent
CMT PASUBTOC block sent
CMT PAPUBKEYS: B1302F79 [RAP Certificate 171 v.1] sent
CMT GENIO_INIT block sent
CMT SOS*UPDAPP block sent
CMT SOS*DSP0 block sent
CMT LDSP block sent
CMT SOS*ISASW block sent
CMT SOS+CORE block sent
CMT SOS+ROFS1 block sent
Prog.status for Asic CMT ...
 NAND: OK
Programming completed in 2 min 34.969 s
Processing PPM file: rm576_071.004_05.01_Russian_prd.rofs2.fpsx 
 [BB5,XSR 1.6]  size: 36.97 MB
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 600C192102031104, 6003192102031104
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Erase size: 47.25 MB
CMT FLASH,MuxOneNAND area [07800000-0A73FFFF]
Prog.status for Asic CMT ...
 NAND: OK
Flash programming ...
CMT SOS+ROFS2 block sent
Prog.status for Asic CMT ...
 NAND: OK
Programming completed in 1 min 5.297 s
Processing PPM file: rm576_071.004_C00.01_DEFAULT_prd.rofs3.fpsx 
 [BB5,XSR 1.6]  size: 8.01 KB
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 600C192102031104, 6003192102031104
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Erase size: 14 MB
CMT FLASH,MuxOneNAND area [0A740000-0B53FFFF]
Prog.status for Asic CMT ...
 NAND: OK
Flash programming ...
CMT SOS+ROFS3 block sent
Prog.status for Asic CMT ...
 NAND: OK
Programming completed in 0.235 s
Processing CNT file: RM576_ENO_11w02v0.049_APE.fpsx 
 [BB5,XSR 1.6]  size: 2.28 MB
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 600C192102031104, 6003192102031104
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Erase size: 4 MB
CMT FLASH,MuxOneNAND area [004E0000-008DFFFF]
Prog.status for Asic CMT ...
 NAND: OK
Flash programming ...
CMT SOS*ENO block sent
Prog.status for Asic CMT ...
 NAND: OK
Programming completed in 4.313 s
Processing CNT file: rm576_071.004_UPink003.000_prd.uda.fpsx 
 [BB5,XSR 1.6]  size: 3.55 MB
 Supported Ids: 4003192102001104, 400C192102001104, 6003192102001104, 600C192102001104, 6003192102011104, 600C192102011104, 6003192102021104, 600C192102021104, 600C192102031104, 6003192102031104
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Erase size: 65 MB
CMT FLASH,MuxOneNAND area [0B540000-0F63FFFF]
Prog.status for Asic CMT ...
 NAND: OK
Flash programming ...
Prog.status for Asic CMT ...
 NAND: OK
Programming completed in 6.891 s
Total time for flashing process(boot+erase+write) was 4 min 3.234 s
 
 
Phone type: RM-576 (Nokia 6700s)
SW version: V ICPR82_11w16.3 19-05-11 RM-576 (c) Nokia 
ApeCoreSw: 071.004
Imei plain: 35339004655544-5
Product code: 0589660
Battery voltage: 4790 mV, current: 53 mA
Language Pack:
- not available.

SLPA ver[4]: PA_SL3/PA_SIMLOC30 (15 digit NCK)
warning: avoid SW Downgrade & manual erase to this phone !
 
SIMLOCK seems to be valid
SUPERDONGLE_KEY seems to be valid
CMLA_KEY seems to be valid
WMDRM_PD seems to be valid
SIMLOCK_TEST passed
SECURITY_TEST passed
 
 
Imei net: 353390046555445
Version: SIMLOCK SERVER
Counter: 0/3, 0/10
 
CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000
 
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

[pro-s]

SelfTests

Initializing Tests...
IMEI : 353390046555445 , Phone : RM-576 Nokia 6700s
Get keys...
PASSED | ST_SLEEP_X_LOOP_TEST
PASSED | ST_UEM_CBUS_IF_TEST
PASSED | ST_EAR_DATA_LOOP_TEST
PASSED | ST_SIM_CLK_LOOP_TEST
PASSED | ST_SIM_LOCK_TEST
PASSED | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_MBUS_RX_TX_LOOP_TEST
PASSED | ST_KELVIN_BATVOLTAGE_TEST
->ERROR | ST_KELVIN_VIBRA_TEST
PASSED | ST_KELVIN_CAPACITOR_TEST
PASSED | ST_KELVIN_MISC_TEST
NOT EXECUTED | ST_KELVIN_CHARGING_TEST
PASSED | ST_KELVIN_AUDIO_TEST
PASSED | ST_KELVIN_XEAR_TEST
->ERROR | ST_AMB_LIGHT_SENSOR_TEST
PASSED | ST_USB_CHARGING_TEST
PASSED | ST_IIC_TEST
->ERROR | ST_DIGIMIC_TEST
->ERROR | ST_RAM_IF_TEST
PASSED | ST_LED_CONTROLLER_TEST
PASSED | ST_CDSP_SLEEPCLOCK_FREQ_TEST
PASSED | ST_CDSP_RF_BB_IF_TEST
PASSED | ST_CDSP_RF_SUPPLY_TEST
PASSED | ST_CDSP_TX_IQ_TEST
PASSED | ST_CDSP_TXC_DATA_TEST
PASSED | ST_CDSP_RX_PLL_PHASE_LOCK_TEST
PASSED | ST_CDSP_TX_PLL_PHASE_LOCK_TEST
PASSED | ST_CDSP_WCDMA_TX_POWER_TEST
PASSED | ST_CDSP_RX_IQ_LOOP_BACK_TEST
PASSED | ST_CDSP_GSM_TX_POWER_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_CAMERA_IF_TEST
->ERROR | ST_SEC_CAMERA_IF_TEST
->ERROR | ST_LED_FLASH_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
->ERROR | ST_MAIN_LCD_IF_TEST
PASSED | ST_BT_WAKEUP_TEST
PASSED | ST_ACCEL_IF_TEST
PASSED | ST_VIBRA_TEST
->ERROR | ST_USB_LOOP_TEST
->ERROR | ST_RADIO_TEST
PASSED | ST_LED_FLASH_IF_TEST
SelfTests end