X6-00 RM-559 ошибка самотестирования

[spark75]

Принесли тело, с диагнозом ошибка самотестирования телефона, версия стояла 40, локал есть, прошил bestom 40 версию еще раз, ситуация не исправилась, bsi на месте,селф тест прилагаю, но когда подключаю к бесту, он его не сразу находит, а только через кнопку вкл.

Initializing Tests...
IMEI : 354855045008033 , Phone : RM-559 Nokia X6-00
Get keys...
PASSED | ST_TAHVOINT_TEST
PASSED | ST_UEM_CBUS_IF_TEST
PASSED | ST_EAR_DATA_LOOP_TEST
PASSED | ST_SIM_CLK_LOOP_TEST
PASSED | ST_SIM_IO_CTRL_LOOP_TEST
PASSED | ST_SIM_LOCK_TEST
PASSED | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_BACKUP_BATT_TEST
PASSED | ST_RADIO_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_MBUS_RX_TX_LOOP_TEST
PASSED | ST_AMB_LIGHT_SENSOR_TEST
PASSED | ST_IIC_TEST
PASSED | ST_DIGIMIC_TEST
PASSED | ST_EXT_DEVICE_TEST
PASSED | ST_CDSP_SLEEPCLK_FREQ_TEST
PASSED | ST_CDSP_SLEEPCLOCK_FREQ_TEST
PASSED | ST_CDSP_RF_BB_IF_TEST
PASSED | ST_CDSP_RF_SUPPLY_TEST
PASSED | ST_CDSP_TX_IQ_TEST
PASSED | ST_CDSP_TXC_DATA_TEST
PASSED | ST_CDSP_RX_PLL_PHASE_LOCK_TEST
NOT RUN | ST_CDSP_TX_PLL_PHASE_LOCK_TEST
NOT RUN | ST_CDSP_WCDMA_TX_POWER_TEST
NOT RUN | ST_CDSP_RX_IQ_LOOP_BACK_TEST
NOT RUN | ST_CDSP_GSM_TX_POWER_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_CAMERA_IF_TEST
PASSED | ST_CAMERA_ACCELERATOR_TEST
PASSED | ST_SEC_CAMERA_IF_TEST
PASSED | ST_LED_FLASH_TEST
PASSED | ST_CAMERA_AUTOFOCUS_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
PASSED | ST_MAIN_LCD_IF_TEST
PASSED | ST_TOUCH_STUCK_TEST
PASSED | ST_BT_WAKEUP_TEST
PASSED | ST_WLAN_TEST
PASSED | ST_BT_WLAN_COEXISTENCE_TEST
PASSED | ST_TOUCH_IF_TEST
PASSED | ST_ACCEL_IF_TEST
PASSED | ST_LCD_CONTROLLER_TEST
PASSED | ST_VIBRA_TEST
NOT RUN | ST_USB_LOOP_TEST
PASSED | ST_RADIO_TEST
PASSED | ST_TVOUT_IF_TEST
PASSED | ST_IO_EXPANDER_IF_TEST
SelfTests end

[Артурар]

пишите РМ с SX4 авторизацией

[AQ7]

где чек сл сд секьюрити? логи прошивки?

[spark75]

где чек сл сд секьюрити? логи прошивки?

лог прошивки

card found: S/N 
registered to: 

Connect phone on selected interface...

Core : v1.40 , FlashEngine : v1.23

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-559_40.0.002_prd.core.C00
PPM : RM-559_40.0.002_prd.rofs2.V05
PPM2 : RM-559_40.0.002_C01_prd.rofs3.fpsx
CNT : RM-559_32.0.002_001_000_U001.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID:       000000010000022600010006400C192101051103
CPU ID :       RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID:        00000296
EM1 ID:        00000B22
PUBLIC ID:     163002184EA600526C8E0E3F6BCEF47C9F61634A
ASIC MODE ID:  00
ROOT KEY HASH: 479C6DDE3942E12C429C1D6ADED80371
ROM ID:        4B9B75103E691FF8
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing RAP3NAND ...
Processing PASUBTOC ...
Processing PAPUBKEYS...
Processing UPDAPP ...
Boot Done! :)
TIME : Boot time : 00:00:04
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL -> [2nd] changing...
ADL Server confirm flashmode!
ADL : Auth done...
ADL : ASIC CMT select Ok
   ===Flashing [MCU]===
Erase : Processing RM-559_40.0.002_prd.core.C00
Found 5 areas to erase
Erasing area 0x00040000 - 0x00082FFF, NAND, CMT
Result: 0000
Erasing area 0x00083400 - 0x003FFFFF, NAND, CMT
Result: 0000
Erasing area 0x00400000 - 0x007FFFFF, NAND, CMT
Result: 0000
Erasing area 0x00800000 - 0x00D5FFFF, NAND, CMT
Result: 0000
Erasing area 0x00D60000 - 0x0B71FFFF, NAND, CMT
Result: 0000
Erase partition 0x0A
Partition erase Ok
Partitioning : Ok [5]
TIME : Erase time : 00:00:01
Write : Processing RM-559_40.0.002_prd.core.C00
Total 508 [508/0/0] blocks to write, writing... 
CMT : Writing Hash CERT [ADA]
CMT : Writing Hash CERT [KEYS]
CMT : Writing Hash CERT [PRIMAPP]
CMT : Writing Hash CERT [RAP3NAND]
CMT : Writing Hash CERT [PASUBTOC]
CMT : Writing Hash CERT [PAPUBKEYS]
CMT : Writing Hash CERT [SOS*UPDAPP]
CMT : Writing Hash CERT [SOS*ENO]
CMT : Writing Hash CERT [SOS*DSP0]
CMT : Writing Hash CERT [SOS*ISASW]
CMT : Writing Hash CERT [SOS+CORE]
CMT : Writing Hash CERT [SOS+ROFS1]
TIME : Write time : 00:00:38
MCU Write done
   ===Flashing [PPM]===
Erase : Processing RM-559_40.0.002_prd.rofs2.V05
Found 1 areas to erase
Erasing area 0x07920000 - 0x0A2FFFFF, NAND, CMT
Result: 0000
TIME : Erase time : 00:00:00
Write : Processing RM-559_40.0.002_prd.rofs2.V05
Total 116 [116/0/0] blocks to write, writing... 
CMT : Writing Hash CERT [SOS+ROFS2]
TIME : Write time : 00:00:09
PPM Write done
   ===Flashing [PPM2]===
Erase : Processing RM-559_40.0.002_C01_prd.rofs3.fpsx
Found 1 areas to erase
Erasing area 0x0A300000 - 0x0B71FFFF, NAND, CMT
Result: 0000
TIME : Erase time : 00:00:00
Write : Processing RM-559_40.0.002_C01_prd.rofs3.fpsx
Total 25 [25/0/0] blocks to write, writing... 
CMT : Writing Hash CERT [SOS+ROFS3]
TIME : Write time : 00:00:01
PPM Write done
   ===Flashing [CNT]===
Erase : Processing RM-559_32.0.002_001_000_U001.uda.fpsx
Found 1 areas to erase
Erasing area 0x0B720000 - 0x1EF7FFFF, NAND, CMT
Result: 0000
TIME : Erase time : 00:00:00
Write : Processing RM-559_32.0.002_001_000_U001.uda.fpsx
Total 32 [32/0/0] blocks to write, writing... 
TIME : Write time : 00:00:02
CNT Write done
 =================
ADL : End flashing
ADL : Finalize...

Flashing done!
Total flash time : 00:00:55
Reboot phone now...

Reading Phone Info....
Connected phone -   Nokia X6-00
Software Info:     V ICPR72_11w16.1 28-07-11 RM-559 (c) Nokia
IMEI:  354855047230353
Ape Version: V 40.0.002
Product code:  0589483
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:01:18
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info...  - Ok

[ЭксПрогматор]

лог прошивки необходимо оформлять тегом [code][/code]!

[genaVL]

но когда подключаю к бесту, он его не сразу находит, а только через кнопку вкл.

Конечно, через внопку вкл., Х6 по USB не заряжается.

Сделай все сбросы и формат, попробуй отформатировать встроенную флэш-память. Можно записать контент, в NaviFirm есть для всех видов -8,16 и 32 Gb, только что проверил.

[spark75]

всем спасибо за помощь, но оказалось BSI, кинул мычку и все пошло, хотя все звонилось нормально, видно где то микротрещина..., еще раз всем спасибо, и проверяем BSI