nikodim
17.03.2011, 16:17
Телефон не моченый, следов удара нет. При подключении к RIFF-
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung i8510 PDA]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07B3602F - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: RAM memory selftest failed.
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung i8510 PDA]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07B3602F - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is 100 kHz
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: RAM memory selftest failed.
Можно ли по сообщению "ERROR: RAM memory selftest failed" утверждать о неисправности флешки? Часто ли они выходят в этой модели из строя?
Оборудование исправно, вот пример восстановления S5230-
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung S5230]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x002C/0x00BA (256MB)
Flashing the dead ************...OK
Resurrection complete!
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung i8510 PDA]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07B3602F - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: RAM memory selftest failed.
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung i8510 PDA]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07B3602F - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is 100 kHz
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...FAILED
ERROR: RAM memory selftest failed.
Можно ли по сообщению "ERROR: RAM memory selftest failed" утверждать о неисправности флешки? Часто ли они выходят в этой модели из строя?
Оборудование исправно, вот пример восстановления S5230-
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.20, JTAG Manager Version: 1.28
Selected Resurrector: [Samsung S5230]
Connecting to the dead ************...OK
Detected dead ************ ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip ID: 0x002C/0x00BA (256MB)
Flashing the dead ************...OK
Resurrection complete!