5230 Не включается

[Pizyanov]

По словам клиента выключился при просмотре видео, состояние вибро при включении и все на этом. Инфо считывает, локал есть, селф тесты проходят все (UFS), в нормал не входит. Прошил цыклоном бэкапы сделаны, изменений нет. Вскрыл плата чистая деформаций нет пропаял vilma betti проц флеш RF проц, с пошатыванием, подключая после каждой микросхемы изменений нет. Прошивка заливалась не последняя но без понижения, залит PM без 1,120,308,309, ЕНО rm588_ENO_x_09wk43v0.020.fpsx, полного стирания не делал рылся не могу под него бланк файл найти ( мож конечно искал плохо ) глубоко копать железо не оплатит клиент. Может кто пнет в нужном направлении

Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing RM-588_20.0.005_001_000_U001.uda.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
RM-588_20.0.005_001_000_U001.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR17_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x09E60000-0x0F47FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.890s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 7.906s
Flashing Speed: 6122,44 kBit/S
Restarting MCU...
Processing RM-588_20.0.005_001_000_U001.uda.fpsx (APE)...
Processing RM-588_20.0.005_C01_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
RM-588_20.0.005_C01_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR17_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x09160000-0x09E5FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.78s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 7.594s
Flashing Speed: 6802,96 kBit/S
Restarting MCU...
Processing RM-588_20.0.005_C01_prd.rofs3.fpsx (APE)...
Processing RM-588_20.0.005_C02_prd.rofs3.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
RM-588_20.0.005_C02_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR17_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x09160000-0x09E5FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.78s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS3 Certificate...
Programming Status OK!
All blocks written OK! Time taken 7.922s
Flashing Speed: 6747,78 kBit/S
Restarting MCU...
Processing RM-588_20.0.005_C02_prd.rofs3.fpsx (APE)...
Processing RM-588_20.0.005_prd.core.C00 (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
RM-588_20.0.005_prd.core.C00, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR17_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00040000-0x00082FFF, ONENAND
EraseArea[0,CMT]: 0x00083400-0x003FFFFF, ONENAND
EraseArea[0,CMT]: 0x00800000-0x00D5FFFF, ONENAND
EraseArea[0,CMT]: 0x00D60000-0x09E5FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 0.890s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 122.735s
Flashing Speed: 6990,48 kBit/S
Restarting MCU...
Processing RM-588_20.0.005_prd.core.C00 (APE)...
Processing RM-588_20.0.005_prd.rofs2.V05 (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
RM-588_20.0.005_prd.rofs2.V05, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR17_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x06DE0000-0x0915FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.203s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 33.0s
Flashing Speed: 6854,32 kBit/S
Restarting MCU...
Processing RM-588_20.0.005_prd.rofs2.V05 (APE)...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
Factory defaults OK
Reading info...
MCU Version V ICPR72_10w04.5
MCU Date 22-03-10
Product RM-588 (Nokia 5230)
Manufacturer (c) Nokia
IMEI 356051038771187
Mastercode 6564722057
IMEI Spare 3A65500183771108
IMEI SV 3365500183771118F1000000
CNT v 001_000, 05-03-10, vanilla, RM588
PSN CBK193494
Product Code 0593017
Basic Product Code 0584528
PSD 0000000000000000
LPSN 0
APE SW V 20.0.005
APE Variant V 20.0.005V 20.0.005
APE Test rm588_ENO_x_09wk43v0.020
APE HW 256
APE ADSP 256
RETU 16
TAHVO 22
AHNE 11
HW 0501
RFIC 17141716
DSP simon_ICPR72_10w05
Simlock Server SIMLOCK SERVER
Simlock Key 2440700000000000
Simlock Profile 0000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [1,2] State: OPENED Type: GID Data: FFFF
Simlock [1,3] State: OPENED Type: GID Data: FFFF
Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [2,2] State: OPENED Type: GID Data: FFFF
Simlock [2,3] State: OPENED Type: GID Data: FFFF
Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [3,2] State: OPENED Type: GID Data: FFFF
Simlock [3,3] State: OPENED Type: GID Data: FFFF
Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [4,2] State: OPENED Type: GID Data: FFFF
Simlock [4,3] State: OPENED Type: GID Data: FFFF
Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [5,2] State: OPENED Type: GID Data: FFFF
Simlock [5,3] State: OPENED Type: GID Data: FFFF
Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [6,2] State: OPENED Type: GID Data: FFFF
Simlock [6,3] State: OPENED Type: GID Data: FFFF
Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [7,2] State: OPENED Type: GID Data: FFFF
Simlock [7,3] State: OPENED Type: GID Data: FFFF
Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
Failed to set Normal Mode -> Mode not accepted

[Mihail_tm]

Нет под него blank,проверь BSI

[azis29]

Флешка какая стоит?

[uo5oq]

... Прошивка заливалась не последняя но без понижения, ..., полного стирания не делал рылся не могу под него бланк файл найти ...
1. Если есть Local, то Cyclone без проблемм забэкапит SLD, SDD, NPC (сделайте это в 1-ю очередь).
2. Запишите SW выше чем было в ТА, желательно самую свежую по INI из полного Nokia SW Installer.
Если после этого не включится то:
3. Стирайте полностью, пишите только SW
Если и после этого не включится - смотрите железо более основательно.

[Pizyanov]

флеш по логу видно Samsung.Бекапы сделал, стереть как не знаю (не нашел бланк) бсай относительно общего звониться локал-тест переключается

[azis29]

стереть как не знаю (не нашел бланк)
Бланк не стирает, есть файл "erase" c ними надо стирать!
Прошей его как MCU!

[uo5oq]

флеш по логу видно Samsung.Бекапы сделал, стереть как не знаю (не нашел бланк) бсай относительно общего звониться локал-тест переключается
Все признаки нарушения ПО.
Blanc нет для этой модели, стирайте полностью.

http://www.mobile-files.ru/forum/attachment.php?attachmentid=125652&stc=1&d=1317288327

[Pizyanov]

если у Вас есть выложте пожалуйста. А кнопки у меня такой нет хотя вроде недавно обновлялся

[Mihail_tm]

если у Вас есть выложте пожалуйста.

Выложить что?

[Pizyanov]

бланк , уже выложил azis29 вот только циклон его шить не желает да и файлы для бб5 он сам выбирает так что говорить что ето мсу я не умею а у УФС загрузчиков нет для этого аппарата

[Mihail_tm]

бланк , уже выложил azis29 вот только циклон его шить не желает да и файлы для бб5 он сам выбирает так что говорить что ето мсу я не умею а у УФС загрузчиков нет для этого аппарата

во первых это не blank,а erase фаил,во вторых,обнови Cyclone,что бы не было гемороя со стиранием

[azis29]

бланк , уже выложил azis29 вот только циклон его шить не желает да и файлы для бб5 он сам выбирает так что говорить что ето мсу я не умею а у УФС загрузчиков нет для этого аппарата

Сколько можно сказать что на это модель нет бланк!

[Pizyanov]

Уже обновил циклон и стер я наверное глупый человек непонимающий отличия в этих файлах но написал что мне нужно стереть аппарат и что обновить циклон надо я понял из поста 7. если расстрелять всех глупых на чьём фоне умным выглядеть

Восстановил после стирания SW 50.0.001 , нет изменений, рою железо
Вру изменения есть
tarted Phone Security Analysis...
MCU Version V ICPR72_10w04.5
MCU Date 22-03-10
Product RM-588 (Nokia 5230)
Manufacturer (c) Nokia
IMEI 356051038771187
Mastercode 6564722057
Reading Security Block...
Security block OK and saved to "RM-588_356051038771187_30.09.2011_121500.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 14000218C48200521E5599718F82516CF0EF7323
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.24.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.11.24.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 7DC72D3FDC552426A4479BC820097D304CFB6C15
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"14000218C48200521E5599718F82516CF0EF7323.C0003CAE" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Analyze finished!

не полный рпл походу, становиться все интереснее

[Pizyanov]

на SW 20.0.005 циклон не вправил SD
на SW 10.0.067 сделал
Started Phone Security Analysis...
MCU Version V ICPR72_09w36.5
MCU Date 25-09-09
Product RM-588 (Nokia 5230)
Manufacturer (c) Nokia
IMEI 356051038771187
Mastercode 6564722057
Reading Security Block...
Security block OK and saved to "RM-588_356051038771187_01.10.2011_123140.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"14000218C48200521E5599718F82516CF0EF7323.C0003CAE" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!
осталось включить :) занимаюсь между делом vilma betti поменяны, плата в идеалепрошлый пост бы подредактировал но кнопка уже исчезла, извените за ап
n2390 заменен Vcore не изменилось 1.25в при включении
перекатан rapido