asrar
24.03.2015, 00:25
Поделитесь дампом.
вот http://bbs.emmchome.com/thread-1981-1-3.html здесь есть только немогу скачать нужны 500 звёзды.
Вот лог SkyHynix H9TP32A8JDAC
Z3X EasyJtag Software ver. 1.8.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0------------------, ,FW Ver.: 01.52
CMD Pullup Level:2031 mV
CMD Active Level:2124 mV
eMMC Device Information
EMMC CID : 90014A4834473164048600A3714F114E
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 01/2014 Rev.0x86
EMMC NAME: H4G1d , S/N: 10711375
EMMC NAME (HEX): 48344731640000
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.
Вот SD7DP28C-4G
Z3X EasyJtag Software ver. 1.8.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: ---------------------, ,FW Ver.: 01.52
CMD Pullup Level:2165 mV
CMD Active Level:2609 mV
eMMC Device Information
EMMC CID : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE
EMMC CSD : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 10/2014 Rev.0x86
EMMC NAME: , S/N: 27559441
EMMC NAME (HEX): 00000000000000
EMMC ROM1 (Main User Data) Capacity: 65536 MB
EMMC ROM2 (Boot Partition 1) Capacity: 0 kB
EMMC ROM3 (Boot Partition 2) Capacity: 0 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: Yes
Extended CSD rev 1.0 (MMC 4.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: _ 27559441_20150202_0112.extcsd
Done.
лог с второго тела тоже не стартует.
Можно хоть дамп рабочий дамп снять с этой флешки?
вот http://bbs.emmchome.com/thread-1981-1-3.html здесь есть только немогу скачать нужны 500 звёзды.
Вот лог SkyHynix H9TP32A8JDAC
Z3X EasyJtag Software ver. 1.8.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0------------------, ,FW Ver.: 01.52
CMD Pullup Level:2031 mV
CMD Active Level:2124 mV
eMMC Device Information
EMMC CID : 90014A4834473164048600A3714F114E
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 01/2014 Rev.0x86
EMMC NAME: H4G1d , S/N: 10711375
EMMC NAME (HEX): 48344731640000
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.
Вот SD7DP28C-4G
Z3X EasyJtag Software ver. 1.8.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: ---------------------, ,FW Ver.: 01.52
CMD Pullup Level:2165 mV
CMD Active Level:2609 mV
eMMC Device Information
EMMC CID : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE
EMMC CSD : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 10/2014 Rev.0x86
EMMC NAME: , S/N: 27559441
EMMC NAME (HEX): 00000000000000
EMMC ROM1 (Main User Data) Capacity: 65536 MB
EMMC ROM2 (Boot Partition 1) Capacity: 0 kB
EMMC ROM3 (Boot Partition 2) Capacity: 0 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: Yes
Extended CSD rev 1.0 (MMC 4.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: _ 27559441_20150202_0112.extcsd
Done.
лог с второго тела тоже не стартует.
Можно хоть дамп рабочий дамп снять с этой флешки?