PDA

Просмотр полной версии : Nokia TA-1021 (PLE) нужен бутфикс



oriforif
27.11.2018, 10:51
Я так понял что NTOOL шьет только через фастбут. Принесли 900E. Соответственно нужно прошить сначала бут а потом шить NTOOL?

britanec
27.11.2018, 10:59
через EDL

ЭксПрогматор
27.11.2018, 11:01
через EDL
незнаю про 6, но была 5 nokia и там с какой-то версии EDL нет даже через TP...

oriforif
27.11.2018, 11:03
через EDL

TA разобран. Тест поинт переводит его в 9008. Шью через Инфинити....но опять 900E. Видимо там стояла версия андроид 8. А таковой нет в cети)))

andrei_d1978
27.11.2018, 14:01
900E я ловил после того как память меняли, на таком, родная память совсем мертвая была, ничего не считать было. Шился вдоль и поперек. Возможно есть привязка?
Тогда тоже решил что в SBL уже прописался 8й андроид, проблему не решил, отдал без ремонта.
Но другой Nokia TA-1021 сейчас клиент принес не загружающийся, что характерно говорит игрался и откатом на 7й андроид и снова на 8й, еще и игрался с разблокировкой, заблокировкой bootloader
в 9008 или 900E он не упал у него.
Бум разбираться

oriforif
27.11.2018, 14:24
900E я ловил после того как память меняли, на таком, родная память совсем мертвая была, ничего не считать было. Шился вдоль и поперек. Возможно есть привязка?
Тогда тоже решил что в SBL уже прописался 8й андроид, проблему не решил, отдал без ремонта.
Но другой Nokia TA-1021 сейчас клиент принес не загружающийся, что характерно говорит игрался и откатом на 7й андроид и снова на 8й, еще и игрался с разблокировкой, заблокировкой bootloader
в 9008 или 900E он не упал у него.
Бум разбираться

А есть бекап под финик?

andrei_d1978
27.11.2018, 14:43
А есть бекап под финик?
под 8й андроид у меня точно нет бекапа.

oriforif
27.11.2018, 14:50
Мда....nbx не конвертится. Придется ждать помощи the_laser! Либо искать аппарат на 8 андроид.

the_laser
27.11.2018, 18:58
буту ( до момента fastboot, то бишь до прошивания) на версию андроида пофиг исключительно.
что там джейди называет бутом, я понятие не имею, сейчас прицеплю нормальный набор для починки из EDL до fastboot

oriforif
27.11.2018, 19:28
буту ( до момента fastboot, то бишь до прошивания) на версию андроида пофиг исключительно.
что там джейди называет бутом, я понятие не имею, сейчас прицеплю нормальный набор для починки из EDL до fastboot

181508
итак бесконечно

oriforif
28.11.2018, 13:48
Нашел дамп. Прошил. В фастбут теперь входит. Но при прошивке ошибка(((
181512
А какие правила по прошивке? 10 кредитов 1 телефон или 10 кредитов 1 прошивка? просто кредиты закончились((

andrei_d1978
28.11.2018, 16:02
Я заливал с поддержки PLE-560C-0-00WW-B01_Android_8.1.0.NBx вчера, все ок
Было заявлено 10 кредитов 1 телефон

oriforif
28.11.2018, 16:04
Я заливал с поддержки PLE-560C-0-00WW-B01_Android_8.1.0.NBx вчера, все ок
Было заявлено 10 кредитов 1 телефон

на этот же телефон у меня программа просит кредиты(((

andrei_d1978
28.11.2018, 16:16
на этот же телефон у меня программа просит кредиты(((
Они может просто должны быть на счету, и не спишутся?

oriforif
28.11.2018, 16:18
Они может просто должны быть на счету, и не спишутся?

не знаю. сейчас закажу еще 20 кредитов. посмотрим.

D1C-562D-0-00WW-B01_Android_8.1.0.NBx прошился этой версией. Кредиты не списались. Работает)
Видимо шить нужно прошивку не ниже которая есть. и фиксбуты также.
Вопрос по ревизиям: в чем отличия PLE и D1C?

the_laser
29.11.2018, 22:01
181508
итак бесконечно

плохой загрузчик.
поменял, ну или можно использовать с поддержки ND1_BootFix.zip ( в каталоге ND1 )


не знаю. сейчас закажу еще 20 кредитов. посмотрим.

D1C-562D-0-00WW-B01_Android_8.1.0.NBx прошился этой версией. Кредиты не списались. Работает)
Видимо шить нужно прошивку не ниже которая есть. и фиксбуты также.
Вопрос по ревизиям: в чем отличия PLE и D1C?


PLE и D1C это разные телефоны


Они может просто должны быть на счету, и не спишутся?

именно так


Нашел дамп. Прошил. В фастбут теперь входит. Но при прошивке ошибка(((


это я накосячил, поправил в v0.041

nkman
04.12.2018, 10:18
Пришел ТА висящий на заставке. Из тестпоинта получится восстановить?

the_laser
04.12.2018, 22:32
Пришел ТА висящий на заставке. Из тестпоинта получится восстановить?

а что, в фастбут не входит ? если входит - прошей просто ...

nkman
06.12.2018, 09:22
а что, в фастбут не входит ? если входит - прошей просто ...

Не входит никуда. Висит на надписи андроид и все.

the_laser
06.12.2018, 18:37
попробуй подсоедини аппарат кабелем, потом зажми volume up + power секунд на 15-20, он сбросится - появится ли какое-либо устройство

oriforif
06.12.2018, 19:50
Не входит никуда. Висит на надписи андроид и все.

что появляется в диспетчере устройств при подключении?

nkman
07.12.2018, 09:57
попробуй подсоедини аппарат кабелем, потом зажми volume up + power секунд на 15-20, он сбросится - появится ли какое-либо устройство

Зашел в download.Теперь нужна прошивка 8.0 я так понимаю. Чтобы прошить через нтул надо купить кредиты?

nkman
07.12.2018, 15:28
Как попасть на сервер поддержки и скачать прошивку?

nkman
07.12.2018, 15:56
Я заливал с поддержки PLE-560C-0-00WW-B01_Android_8.1.0.NBx вчера, все ок
Было заявлено 10 кредитов 1 телефон

Все разобрался.

nkman
07.12.2018, 16:39
07.12.2018 16:55:29 RUNNING NTool 0.041
07.12.2018 16:55:33 SERVER CREDITS LEFT/USED: 20/0
07.12.2018 16:55:33 Elapsed: 0 secs.
07.12.2018 17:34:57
07.12.2018 17:34:57 SELECT FIRMWARE PACKAGE
07.12.2018 17:35:04 Will flash : PLE-560I-0-00WW-B01.NBx
07.12.2018 17:35:04 PLEASE CONNECT POWERED OFF PHONE
07.12.2018 17:35:17 PHONE "PLEGAR17C2209848" CONNECTED
07.12.2018 17:35:18 ProjectCode : PLE
07.12.2018 17:35:18 model : PAD
07.12.2018 17:35:18 sub_model : none
07.12.2018 17:35:18 software version : PLE-522A-0-00WW-B04
07.12.2018 17:35:18 SW model : 00WW
07.12.2018 17:35:18 build number : B04
07.12.2018 17:35:18 hardware version : 5.1
07.12.2018 17:35:18 RF band id :
07.12.2018 17:35:18 _850_900_1800_1900^W_1_2_5_8^L_1_3_5_7_8_20_28_38_40
07.12.2018 17:35:18 chip version : none
07.12.2018 17:35:18 MCP info : none
07.12.2018 17:35:18 EMMC version : Unknown 5.1 32GB
07.12.2018 17:35:18 secure : yes
07.12.2018 17:35:18 Bootloader type : commercial
07.12.2018 17:35:19 Download size : 00000511 mB
07.12.2018 17:35:20 Security version : 0004
07.12.2018 17:35:20 Challenge : 11800cff9f5cf34dd630d33757efe36dd542b5a5
07.12.2018 17:35:20 Waiting for calculation process ...
07.12.2018 17:35:20 RESPONSE: "SUCCESS" [256]
07.12.2018 17:35:21 BOOTLOADER AUTH PASSED
07.12.2018 17:35:21 Flash "D1C-0-560C-emmc_appsboot_service.zip" to "aboot"
07.12.2018 17:36:01 FATAL ERROR: Failed to write "aboot", error : "flash write failure"
07.12.2018 17:36:01 Elapsed: 43 secs.

В чем проблема? И почему D1C льет, хотя скачал для PLE

the_laser
07.12.2018, 19:42
проблема с eMMC

nkman
08.12.2018, 11:44
проблема с eMMC

Дамп есть у кого?

the_laser
08.12.2018, 17:37
Дамп есть у кого?

зачем тебе дамп, если на нее не записывается ?
читай с нее дамп и пиши в чистую.

nkman
14.01.2019, 13:39
Пришла еще одна Нокиа 6. При прошивке такой же лог. Что и у него флеха умерла? Может все же в чем то другом дело?

the_laser
14.01.2019, 15:40
и все же дело в eMMC.



.............
if (mmc_write(ptn , sz, (unsigned int *)data)) {
fastboot_fail("flash write failure");
return;

CHEKM
28.01.2019, 18:47
Тоже флеша?

SELECT FIRMWARE PACKAGE
Elapsed: 7 secs.

SELECT FIRMWARE PACKAGE
Will flash : PLE-558B-0-00WW-B01.mlf
PLEASE CONNECT POWERED OFF PHONE
PHONE "PLEGAR17C1310436" CONNECTED
ProjectCode : PLE
model : PAD
sub_model : none
software version : PLE-558E-0-00WW-B01
SW model : 00WW
build number : B01
hardware version : 5.1
RF band id :
_850_900_1800_1900^W_1_2_5_8^L_1_3_5_7_8_20_28_38_40
chip version : none
MCP info : none
EMMC version : Unknown 5.1 32GB
secure : yes
Bootloader type : service
Download size : 00000511 mB
Security version : 0001
ProjectCode : PLE
UID : 43f544d15a878b02f04d323d799dd940c3d8429e
Waiting for calculation process ...
RESPONSE: "SUCCESS" [256]
SERVICE AUTH PASSED
Perform auth routine
Flash "PLE-0-558B-gpt_both0.bin" to "partition"
Skip flashing "D1C-0-558B-emmc_appsboot_service.mbn"
Skip flashing "D1C-0-558B-emmc_appsboot_service.mbn"
Flash "D1C-0-558B-rpm.mbn" to "rpm"
Flash "D1C-0-558B-rpm.mbn" to "rpmbak"
Flash "D1C-0-558B-sbl1.mbn" to "sbl1"
Flash "D1C-0-558B-sbl1.mbn" to "sbl1bak"
Flash "D1C-0-558B-tz.mbn" to "tz"
Flash "D1C-0-558B-tz.mbn" to "tzbak"
Flash "D1C-0-558B-hwcfg.img" to "hwcfg"
Flash "D1C-0-558B-adspso.bin" to "dsp"
Flash "D1C-0-558B-cmnlib.mbn" to "cmnlib"
Flash "D1C-0-558B-cmnlib.mbn" to "cmnlibbak"
Flash "D1C-0-558B-cmnlib64.mbn" to "cmnlib64"
Flash "D1C-0-558B-cmnlib64.mbn" to "cmnlib64bak"
Flash "D1C-0-558B-devcfg.mbn" to "devcfg"
Flash "D1C-0-558B-devcfg.mbn" to "devcfgbak"
Flash "D1C-0-558B-keymaster.mbn" to "keymaster"
Flash "D1C-0-558B-keymaster.mbn" to "keymasterbak"
Perform fastboot command "reboot-bootloader"
PHONE "PLEGAR17C1310436" REMOVED
PHONE "PLEGAR17C1310436" CONNECTED
Perform auth routine
Security version : 0001
ProjectCode : PLE
UID : 43f544d15a878b02f04d323d799dd940c3d8429e
Waiting for calculation process ...
RESPONSE: "SUCCESS" [256]
SERVICE AUTH PASSED
Flash "PLE-00WW-013-splash.img" to "splash"
Flash "D1C-0-558B-ftm.img" to "ftmboot"
Flash "PLE-00WW-013-multi-splash.img" to "multi_splash"
Flash "PLE-0-558B-00WW-boot.img" to "boot"
Flash "PLE-0-558B-00WW-system.img" to "system"
WriteCommBlockInt : Присоединенное к системе устройство не работает
WriteCommBlock blk write fail
FATAL ERROR: write error while downloading "system"
Elapsed: 13 secs.

Вот не знал ещё одного
за кнопку boot unlock снимается по 10 кредитов при каждом нажатии на неё
Думал 1 раз спишется и всё(с неудачной прошивкой уже списало 40 кредитов)

токен на разблокировку как применять?
так не работает
181966

the_laser
29.01.2019, 11:53
возможно, прозаично разряженный аккумулятор - устройство просто ушло из системы, как если бы кабель вытащили

про кредиты, сорян, читай потребление кредитов.



install fastboot drivers for phone.
power off phone.

run
fastboot -i 0x2e04 flash unlock <signature file>
connect phone to cable
run
fastboot -i 0x2e04 oem unlock-go
follow instructions on phone display if any

matero
20.03.2019, 17:22
Зашла Nokia 6 TA-1021 на крышке
182314

компом видится как 900E
На дисплее пишет "you phone has ever been rooted..."
182315
Пробовал identify через ntool- не видится никак

Уже до меня мыкался тест поинт.
Через тест поинт вгоняется в 9008, но ntool тоже не видится
Зацепил InfinityBox CM2QLM
182316
видится почему то как TA-1025
ps- слил на всякий через CM2QLM бекап

попробовал бутфикс из поста #9


<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 00000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: -1 physical_partition_number: 0 filename: DISK value: 0 crc_size 9
2
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-1,
92)" what="Update Backup Header with CRC of Backup Header."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
59, over bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 8830A099" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
Status: 0 The operation completed successfully.


c:\PLE_D1C_ND1_BootFix>emmcdl.exe -p COM19 -f D1C-0-3700-prog_emmc_firehose_8937
_lite.mbn -x PLE-0-3140-patch0.xml
Version 2.10
PblHack: Error - 1836597052
Did not receive Sahara hello packet from device

!!!!!!!! WARNING: Flash programmer failed to load trying to continue !!!!!!!!!

.0" encoding="UTF-8" ?><data><log value="XML (0 bytes) not validated" /></data><
?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" /></data>
Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="1048576"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Host's payload to targe
t size is too large" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

---Target returned NAK---

We are decreasing our max packet size 16384


Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="16384"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
Connected to flash programmer, starting download
start_sector: 17 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 start_sector: 17 physical_partition_number: 0 fi
lename: DISK value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_I
N_BYTES="512" byte_offset="296" filename="DISK" physical_partition_number="0" si
ze_in_bytes="8" start_sector="17" value="NUM_DISK_SECTORS-34" what="Update last
partition 63 'userdata' with actual size in Primary Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 17 with
03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 15 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 start_sector: -18 physical_partition_number: 0 f
ilename: DISK value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_I
N_BYTES="512" byte_offset="296" filename="DISK" physical_partition_number="0" si
ze_in_bytes="8" start_sector="NUM_DISK_SECTORS-18" value="NUM_DISK_SECTORS-34" w
hat="Update last partition 63 'userdata' with actual size in Backup Header."/></
data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071342
with 03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 start_sector: 1 physical_partition_number: 0 file
name: DISK value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="48" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="1" value="NUM_DISK_SECTORS-34" what="Update Primary
Header with LastUseableLBA"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
3A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="48" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-34" what
="Update Backup Header with LastUseableLBA."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -1 crc_size -858993460
patch_offset: 32 patch_size: 8 start_sector: 1 physical_partition_number: 0 file
name: DISK value: -1 crc_size -858993460
patch_offset: 32 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="32" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="1" value="NUM_DISK_SECTORS-1" what="Update Primary H
eader with BackupGPT Header Location"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
3A3DFFF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -1 crc_size -858993460
patch_offset: 24 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -1 crc_size -858993460
patch_offset: 24 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="24" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-1" what=
"Update Backup Header with CurrentLBA."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFFF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -33 crc_size -858993460
patch_offset: 72 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -33 crc_size -858993460
patch_offset: 72 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="72" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-33" what
="Update Backup Header with Partition Array Location"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFDF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: DISK value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="88" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="CRC32(2,8192)" what="Update Primary Header
with CRC of Partition Array"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 2, ove
r bytes 8192" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 3
9FCAFAD" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="88" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-33
,8192)" what="Update Backup Header with CRC of Partition Array."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
27, over bytes 8192" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 39FCAFAD" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: 0 crc_size 8192
patch_offset: 16 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: PLE-0-3140-gpt_main0.bin value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: DISK value: 0 crc_size 92
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="0" what="Zero Out Header CRC in Primary He
ader"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
0000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: DISK value: 0 crc_size 92

patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="CRC32(1,92)" what="Update Primary Header w
ith CRC of Primary Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 1, ove
r bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 6
4BB2881" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: 32 physical_partition_number: 0 fil
ename: PLE-0-3140-gpt_backup0.bin value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: 0 crc_size 92
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="0" what="Zero Out Header
CRC in Backup Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 00000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: -1 physical_partition_number: 0 filename: DISK value: 0 crc_size 9
2
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-1,
92)" what="Update Backup Header with CRC of Backup Header."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
59, over bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 8830A099" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
Status: 0 The operation completed successfully.


c:\PLE_D1C_ND1_BootFix>emmcdl.exe -p COM19 -f D1C-0-3700-prog_emmc_firehose_8937
_lite.mbn -r
Version 2.10
PblHack: Error - 1836597052
Did not receive Sahara hello packet from device

!!!!!!!! WARNING: Flash programmer failed to load trying to continue !!!!!!!!!

.0" encoding="UTF-8" ?><data><log value="XML (0 bytes) not validated" /></data><
?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" /></data>
Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="1048576"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Host's payload to targe
t size is too large" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

---Target returned NAK---

We are decreasing our max packet size 16384


Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="16384"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
Connected to flash programmer, starting download
Programming RAW command: <?xml version="1.0" ?><data><power value="reset" /></da
ta>


<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>nSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

Status: 0 The operation completed successfully.

Для продолжения нажмите любую клавишу . . .

c:\PLE_D1C_ND1_BootFix>if "1" == "0" echo WARNING: Could not find any connected
Qualcomm HS-USB QDLoader 9008.

c:\PLE_D1C_ND1_BootFix>echo.


c:\PLE_D1C_ND1_BootFix>endlocal

c:\PLE_D1C_ND1_BootFix>pause
Для продолжения нажмите любую клавишу . . .

c:\PLE_D1C_ND1_BootFix>goto :EOF

c:\PLE_D1C_ND1_BootFix>

Теперь на мгновение в диспетчере проскакивает как adb
182317

не пойму что ему надо, уже все комбинации кнопок перепробовал- все равно не видится ntool
на дисплее по прежнему "you phone has ever been rooted"

the_laser
20.03.2019, 17:36
а ты драйвера поставь для adb из NTool\drivers

ессно, придется тебе,скорее всего, вручную их поменять в диспетчере устройств вместо самсунговских.

matero
22.03.2019, 16:16
Прошил.
Было так

RUNNING NTool 0.045

SELECT FIRMWARE PACKAGE
Will flash : PLE-560I-0-00WW-B01.NBx
PLEASE CONNECT POWERED OFF PHONE
PHONE "PLEGAR17C1501094" CONNECTED
Project : PLE
model : PAD
sub_model : none
software version : PLE-558H-0-00WW-B01
SW model : 00WW
build number : B01
hardware version : 5.1
RF band id :
_850_900_1800_1900^W_1_2_5_8^L_1_3_5_7_8_20_28_38_40
chip version : none
MCP info : none
EMMC version : Unknown 5.1 32GB
secure : yes
Bootloader type : commercial
Download size : 00000511 mB
Security version : 0004
Challenge : e116dddc9ec3ba10d4014a57112d922d93489acd
Waiting for calculation process ...
server error: bad username/password.
FATAL ERROR: server error: No server found.
Elapsed: 3 secs.

После прошивки теперь версия поменялась


Elapsed: 494 secs.
PHONE "PLEGAR17C1501094" CONNECTED
Project : PLE
model : PAD
sub_model : none
software version : PLE-560I-0-00WW-B01
SW model : 00WW
build number : B01
hardware version : 5.1
RF band id :
_850_900_1800_1900^W_1_2_5_8^L_1_3_5_7_8_20_28_38_40
chip version : none
MCP info : none
EMMC version : Unknown 5.1 32GB
secure : yes
Bootloader type : commercial
Download size : 00000511 mB
Elapsed: 30 secs.

182326
на дисплее по прежнему "you phone has ever been rooted"
Что-то еще можно придумать?

the_laser
22.03.2019, 21:59
да можно конечно.
флажок сбросить надо в разделе deviceinfo

сделаю команду, чтобы разделы читать можно было и потом напишу что да как.

Radiotrance
30.03.2019, 16:01
Этот аппарат с полного бланка поднимается?
Сдохла eMMC, ничего вычитать не получилось. Получится ли восстановить сеть после замены?

the_laser
30.03.2019, 17:17
если не был залочен когда-то на сеть, можно скопировать eMMC с другого такого же, стереть/занулить разделы securefs,modemst1,modemst2 - технически, должно заработать.
если был залочен на сеть, то розовая птица обломинго - в паблике это не чинится

tomash777
22.04.2019, 14:44
TA-1021 не включается, при подключении - 9008 порт
лог identify в infinity

Wait for phone...
Device Found!
Initialize ...
Handshake passed!
ID_BLOCK_I : SnapDragon 430 [MSM8937]
ID_BLOCK_S : 24718E3A
ID_BLOCK_L : 767C99A9BB310D9A13C8898315D4090B
ID_BLOCK_L : 734126AAAE43EDA8C2992DC461F71E29
Use CM2 Internal Loader
Loader Sent! Initializing ...

ERROR : FH Configuration failed!
HINT : Remove battery, cable. Check cable and connection. Repeat operation!

попытка использовать ND1_BootFix заканчивается ошибками

12:21:02: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --reset
************************************************

12:21:02: DEBUG: Binary build date: May 4 2016 @ 10:02:58

12:21:02: DEBUG: Build Version: 16.05. 4.10.02.58

12:21:02: INFO: Current working dir (cwd): F:\_Mobile\Nokia\Firmware\_HMD\Nokia5\ND1_BootFix\
12:21:02: INFO: Showing network mappings to allow debugging
12:21:02: DEBUG: Новые подключения будут запомнены.

12:21:02: DEBUG:

12:21:02: DEBUG: В списке нет элементов.

12:21:02: DEBUG:

12:21:02: INFO: User wants to talk to port '\\.\COM9'
12:21:02: DEBUG: port_fd=0xDC

12:21:02: INFO: Took 0.00000000 seconds to open port
12:21:02: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
12:21:02: INFO: If you don't want this, use --dontsorttags

12:21:02: INFO: Sending <configure>
12:21:02: DEBUG: CHANNEL DATA (P0000) (H00202) ( 246 bytes) - HOST TO TARGET -->
===========================================================================================================
<?xml version="1.0" encoding="UTF-8" ?>
<data>
<configure MemoryName="eMMC" Verbose="0" AlwaysValidate="0" MaxDigestTableSizeInBytes="8192" MaxPayloadSizeToTargetInBytes="1048576" ZlpAwareHost="1" SkipStorageInit="0" TargetName="8960" />
</data>

============================================================================================================

12:21:02: DEBUG: CharsInBuffer=0 Trying to read from USB 8192 bytes
12:21:02: DEBUG: CHANNEL DATA (16 bytes) <-- TARGET to HOST
12:21:02: DEBUG: CharsInBuffer = 16
12:21:02: DEBUG: printBuffer:4247 PRETTYPRINT Buffer is 16 bytes

12:21:02: DEBUG: printBuffer:4324 04 00 00 00 10 00 00 00 0D 00 00 00 01 00 00 00 ................
12:21:02: DEBUG: printBuffer:4337




_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


12:21:02: {ERROR: DetermineTag:4982 XML not formed correctly. Expected a &lt; character at loc 0


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


12:21:02: {ERROR: GetNextPacket:6095 3. TAG not found or recognized


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


12:21:02: {ERROR: GetNextPacket:6105

There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!

This can mean
1. You forgot to send DeviceProgrammer first (i.e. QSaharaServer.exe -s 13:prog_emmc_firehose_8994_lite.mbn)
2. OR, you did send DeviceProgrammer, but it has crashed and/or is not correct for this target

Regardless this program speaks FIREHOSE protocol and your target is speaking SAHARA protcol, so this will not work



мертвая флеш?

the_laser
24.04.2019, 16:29
сперва
load_firehose.cmd

потом
load_boot.cmd

tomash777
25.04.2019, 17:04
вначале load_firehose.cmd
после load_boot.cmd
лог изменился, но все равно error

14:11:05: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --reset
************************************************

14:11:05: DEBUG: Binary build date: May 4 2016 @ 10:02:58

14:11:05: DEBUG: Build Version: 16.05. 4.10.02.58

14:11:05: INFO: Current working dir (cwd): F:\_Mobile\Nokia\Firmware\_HMD\Nokia5\ND1_BootFix\
14:11:05: INFO: Showing network mappings to allow debugging
14:11:05: DEBUG: Новые подключения будут запомнены.

14:11:05: DEBUG:

14:11:05: DEBUG: В списке нет элементов.

14:11:05: DEBUG:

14:11:05: INFO: User wants to talk to port '\\.\COM9'
14:11:05: DEBUG: port_fd=0xF8

14:11:05: INFO: Took 0.28100000 seconds to open port
14:11:05: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
14:11:05: INFO: If you don't want this, use --dontsorttags

14:11:05: INFO: Sending <configure>
14:11:05: DEBUG: CHANNEL DATA (P0000) (H00202) ( 246 bytes) - HOST TO TARGET -->
===========================================================================================================
<?xml version="1.0" encoding="UTF-8" ?>
<data>
<configure MemoryName="eMMC" Verbose="0" AlwaysValidate="0" MaxDigestTableSizeInBytes="8192" MaxPayloadSizeToTargetInBytes="1048576" ZlpAwareHost="1" SkipStorageInit="0" TargetName="8960" />
</data>

============================================================================================================

14:11:06: DEBUG: Only 0 bytes written of 246 requested, attempt 1 of 100
14:11:06: DEBUG: Only 0 bytes written of 246 requested, attempt 2 of 100
14:11:06: DEBUG: Only 0 bytes written of 246 requested, attempt 3 of 100
14:11:06: DEBUG: Only 0 bytes written of 246 requested, attempt 4 of 100
14:11:07: DEBUG: Only 0 bytes written of 246 requested, attempt 5 of 100
14:11:07: DEBUG: Only 0 bytes written of 246 requested, attempt 6 of 100
14:11:07: DEBUG: Only 0 bytes written of 246 requested, attempt 7 of 100
14:11:07: DEBUG: Only 0 bytes written of 246 requested, attempt 8 of 100
14:11:08: DEBUG: Only 0 bytes written of 246 requested, attempt 9 of 100
14:11:08: DEBUG: Only 0 bytes written of 246 requested, attempt 10 of 100
14:11:08: DEBUG: Only 0 bytes written of 246 requested, attempt 11 of 100
14:11:08: DEBUG: Only 0 bytes written of 246 requested, attempt 12 of 100
14:11:09: DEBUG: Only 0 bytes written of 246 requested, attempt 13 of 100
14:11:09: DEBUG: Only 0 bytes written of 246 requested, attempt 14 of 100
14:11:09: DEBUG: Only 0 bytes written of 246 requested, attempt 15 of 100
14:11:09: DEBUG: Only 0 bytes written of 246 requested, attempt 16 of 100
14:11:10: DEBUG: Only 0 bytes written of 246 requested, attempt 17 of 100
14:11:10: DEBUG: Only 0 bytes written of 246 requested, attempt 18 of 100
14:11:10: DEBUG: Only 0 bytes written of 246 requested, attempt 19 of 100
14:11:10: DEBUG: Only 0 bytes written of 246 requested, attempt 20 of 100
14:11:11: DEBUG: Only 0 bytes written of 246 requested, attempt 21 of 100
14:11:11: DEBUG: Only 0 bytes written of 246 requested, attempt 22 of 100
14:11:11: DEBUG: Only 0 bytes written of 246 requested, attempt 23 of 100
14:11:11: DEBUG: Only 0 bytes written of 246 requested, attempt 24 of 100
14:11:12: DEBUG: Only 0 bytes written of 246 requested, attempt 25 of 100
14:11:12: DEBUG: Only 0 bytes written of 246 requested, attempt 26 of 100
14:11:12: DEBUG: Only 0 bytes written of 246 requested, attempt 27 of 100
14:11:12: DEBUG: Only 0 bytes written of 246 requested, attempt 28 of 100
14:11:13: DEBUG: Only 0 bytes written of 246 requested, attempt 29 of 100
14:11:13: DEBUG: Only 0 bytes written of 246 requested, attempt 30 of 100
14:11:13: DEBUG: Only 0 bytes written of 246 requested, attempt 31 of 100
14:11:14: DEBUG: Only 0 bytes written of 246 requested, attempt 32 of 100
14:11:14: DEBUG: Only 0 bytes written of 246 requested, attempt 33 of 100
14:11:14: DEBUG: Only 0 bytes written of 246 requested, attempt 34 of 100
14:11:14: DEBUG: Only 0 bytes written of 246 requested, attempt 35 of 100
14:11:15: DEBUG: Only 0 bytes written of 246 requested, attempt 36 of 100
14:11:15: DEBUG: Only 0 bytes written of 246 requested, attempt 37 of 100
14:11:15: DEBUG: Only 0 bytes written of 246 requested, attempt 38 of 100
14:11:15: DEBUG: Only 0 bytes written of 246 requested, attempt 39 of 100
14:11:16: DEBUG: Only 0 bytes written of 246 requested, attempt 40 of 100
14:11:16: DEBUG: Only 0 bytes written of 246 requested, attempt 41 of 100
14:11:16: DEBUG: Only 0 bytes written of 246 requested, attempt 42 of 100
14:11:16: DEBUG: Only 0 bytes written of 246 requested, attempt 43 of 100
14:11:17: DEBUG: Only 0 bytes written of 246 requested, attempt 44 of 100
14:11:17: DEBUG: Only 0 bytes written of 246 requested, attempt 45 of 100
14:11:17: DEBUG: Only 0 bytes written of 246 requested, attempt 46 of 100
14:11:17: DEBUG: Only 0 bytes written of 246 requested, attempt 47 of 100
14:11:18: DEBUG: Only 0 bytes written of 246 requested, attempt 48 of 100
14:11:18: DEBUG: Only 0 bytes written of 246 requested, attempt 49 of 100
14:11:18: DEBUG: Only 0 bytes written of 246 requested, attempt 50 of 100
14:11:18: DEBUG: Only 0 bytes written of 246 requested, attempt 51 of 100
14:11:19: DEBUG: Only 0 bytes written of 246 requested, attempt 52 of 100
14:11:19: DEBUG: Only 0 bytes written of 246 requested, attempt 53 of 100
14:11:19: DEBUG: Only 0 bytes written of 246 requested, attempt 54 of 100
14:11:19: DEBUG: Only 0 bytes written of 246 requested, attempt 55 of 100
14:11:20: DEBUG: Only 0 bytes written of 246 requested, attempt 56 of 100
14:11:20: DEBUG: Only 0 bytes written of 246 requested, attempt 57 of 100
14:11:20: DEBUG: Only 0 bytes written of 246 requested, attempt 58 of 100
14:11:20: DEBUG: Only 0 bytes written of 246 requested, attempt 59 of 100
14:11:21: DEBUG: Only 0 bytes written of 246 requested, attempt 60 of 100
14:11:21: DEBUG: Only 0 bytes written of 246 requested, attempt 61 of 100
14:11:21: DEBUG: Only 0 bytes written of 246 requested, attempt 62 of 100
14:11:21: DEBUG: Only 0 bytes written of 246 requested, attempt 63 of 100
14:11:22: DEBUG: Only 0 bytes written of 246 requested, attempt 64 of 100
14:11:22: DEBUG: Only 0 bytes written of 246 requested, attempt 65 of 100
14:11:22: DEBUG: Only 0 bytes written of 246 requested, attempt 66 of 100
14:11:22: DEBUG: Only 0 bytes written of 246 requested, attempt 67 of 100
14:11:23: DEBUG: Only 0 bytes written of 246 requested, attempt 68 of 100
14:11:23: DEBUG: Only 0 bytes written of 246 requested, attempt 69 of 100
14:11:23: DEBUG: Only 0 bytes written of 246 requested, attempt 70 of 100
14:11:24: DEBUG: Only 0 bytes written of 246 requested, attempt 71 of 100
14:11:24: DEBUG: Only 0 bytes written of 246 requested, attempt 72 of 100
14:11:24: DEBUG: Only 0 bytes written of 246 requested, attempt 73 of 100
14:11:24: DEBUG: Only 0 bytes written of 246 requested, attempt 74 of 100
14:11:25: DEBUG: Only 0 bytes written of 246 requested, attempt 75 of 100
14:11:25: DEBUG: Only 0 bytes written of 246 requested, attempt 76 of 100
14:11:25: DEBUG: Only 0 bytes written of 246 requested, attempt 77 of 100
14:11:25: DEBUG: Only 0 bytes written of 246 requested, attempt 78 of 100
14:11:26: DEBUG: Only 0 bytes written of 246 requested, attempt 79 of 100
14:11:26: DEBUG: Only 0 bytes written of 246 requested, attempt 80 of 100
14:11:26: DEBUG: Only 0 bytes written of 246 requested, attempt 81 of 100
14:11:26: DEBUG: Only 0 bytes written of 246 requested, attempt 82 of 100
14:11:27: DEBUG: Only 0 bytes written of 246 requested, attempt 83 of 100
14:11:27: DEBUG: Only 0 bytes written of 246 requested, attempt 84 of 100
14:11:27: DEBUG: Only 0 bytes written of 246 requested, attempt 85 of 100
14:11:27: DEBUG: Only 0 bytes written of 246 requested, attempt 86 of 100
14:11:28: DEBUG: Only 0 bytes written of 246 requested, attempt 87 of 100
14:11:28: DEBUG: Only 0 bytes written of 246 requested, attempt 88 of 100
14:11:28: DEBUG: Only 0 bytes written of 246 requested, attempt 89 of 100
14:11:28: DEBUG: Only 0 bytes written of 246 requested, attempt 90 of 100
14:11:29: DEBUG: Only 0 bytes written of 246 requested, attempt 91 of 100
14:11:29: DEBUG: Only 0 bytes written of 246 requested, attempt 92 of 100
14:11:29: DEBUG: Only 0 bytes written of 246 requested, attempt 93 of 100
14:11:29: DEBUG: Only 0 bytes written of 246 requested, attempt 94 of 100
14:11:30: DEBUG: Only 0 bytes written of 246 requested, attempt 95 of 100
14:11:30: DEBUG: Only 0 bytes written of 246 requested, attempt 96 of 100
14:11:30: DEBUG: Only 0 bytes written of 246 requested, attempt 97 of 100
14:11:30: DEBUG: Only 0 bytes written of 246 requested, attempt 98 of 100
14:11:31: DEBUG: Only 0 bytes written of 246 requested, attempt 99 of 100
14:11:31: DEBUG: Only 0 bytes written of 246 requested, attempt 100 of 100


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


14:11:31: {ERROR: WritePort:3976 Could not write to '\\.\COM9', Windows API WriteFile failed! Your device is probably *not* on this port, attempted 100 times

the_laser
25.04.2019, 18:14
а что сказал load_firehose.cmd ?

tomash777
25.04.2019, 19:14
лог load_firehose.cmd (командная строка)

3. Qualcomm HS-USB QDLoader 9008 is COM9.

C:\ND1_BootFix>QSaharaServer.exe -p \\.\COM9 -s 13:C:\ND1_BootFix\D1C-0-3700-prog_emmc_firehose_8937_lite.mbn
Binary build date: Oct 31 2016 @ 22:51:05
QSAHARASERVER CALLED LIKE THIS: 'QSaharaServer.ex'Current working dir: C:\ND1_BootFix
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: C:\ND1_BootFix\D1C-0-3700-prog_emmc_firehose_8937_lite.mbn

17:02:54: Requested ID 13, file: "C:\ND1_BootFix\D1C-0-3700-prog_emmc_firehose_8937_lite.mbn"

17:02:55: 215044 bytes transferred in 0.125000 seconds (1.6407MBps)



17:02:55: File transferred successfully


NOTE: Target requested image 13 which is DeviceProgrammer. Forcing QUIT. This is by design, ** All is well ** SUCCESS!!


17:02:55: Sahara protocol completed
Для продолжения нажмите любую клавишу . . .

C:\ND1_BootFix>if "1" == "0" echo WARNING: Could not find any connected Qualcomm HS-USB QDLoader 9008.

C:\ND1_BootFix>echo.


C:\ND1_BootFix>endlocal

C:\ND1_BootFix>pause
Для продолжения нажмите любую клавишу . . .
лог load_boot.cmd (командная строка)

3. Qualcomm HS-USB QDLoader 9008 is COM9.

Binary build date: May 4 2016 @ 10:02:58
Build version: 16.05. 4.10.02.58

17:05:01: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --sendxml=D1C-0-3700-rawprogram0.xml --search_path=C:\ND1_BootFix --noprompt --showpercentagecomplete --zlpawarehost=1
************************************************

17:05:01: INFO: Current working dir (cwd): C:\ND1_BootFix\
17:05:01: INFO: Showing network mappings to allow debugging
17:05:01: INFO:



17:05:01: INFO: Trying to store 'D1C-0-3700-rawprogram0.xml' in string table
17:05:01: INFO: Looking for file 'D1C-0-3700-rawprogram0.xml'
17:05:01: INFO: User wants to talk to port '\\.\COM9'
17:05:01: INFO: Took 0.00000000 seconds to open port
17:05:01: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
17:05:01: INFO: If you don't want this, use --dontsorttags

17:05:01: INFO: Looking for file 'D1C-0-3700-sbl1.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-sbl1.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-rpm.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-rpm.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-tz.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-tz.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-devcfg.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-devcfg.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-emmc_appsboot.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-emmc_appsboot.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-sbl1.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-sbl1.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-sbl1.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-hwcfg.img'
17:05:01: INFO: Looking for file 'D1C-0-3700-cmnlib.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-cmnlib.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-cmnlib64.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-cmnlib64.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-keymaster.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-keymaster.mbn'
17:05:01: INFO: Looking for file 'D1C-0-3700-gpt_main0.bin'
17:05:01: INFO:

Total to be tansferd with <program> or <read> is 8.28 MB


17:05:01: INFO: Sending <configure>


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


17:05:27: {ERROR: Could not write to '\\.\COM9', Windows API WriteFile failed! Your device is probably *not* on this port, attempted 100 times}

Writing log to 'C:\ND1_BootFix\port_trace.txt', might take a minute


Log is 'C:\ND1_BootFix\port_trace.txt'


Binary build date: May 4 2016 @ 10:02:58
Build version: 16.05. 4.10.02.58

17:05:27: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --sendxml=D1C-0-3700-patch0.xml --search_path=C:\ND1_BootFix --noprompt --showpercentagecomplete --zlpawarehost=1
************************************************

17:05:27: INFO: Current working dir (cwd): C:\ND1_BootFix\
17:05:27: INFO: Showing network mappings to allow debugging
17:05:27: INFO:



17:05:27: INFO: Trying to store 'D1C-0-3700-patch0.xml' in string table
17:05:27: INFO: Looking for file 'D1C-0-3700-patch0.xml'
17:05:27: INFO: User wants to talk to port '\\.\COM9'
17:05:27: INFO: Took 0.18700000 seconds to open port
17:05:27: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
17:05:27: INFO: If you don't want this, use --dontsorttags

17:05:27: INFO: Sending <configure>


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


17:05:53: {ERROR: Could not write to '\\.\COM9', Windows API WriteFile failed! Your device is probably *not* on this port, attempted 100 times}

Writing log to 'C:\ND1_BootFix\port_trace.txt', might take a minute


Log is 'C:\ND1_BootFix\port_trace.txt'

Waiting: Reset device...

Binary build date: May 4 2016 @ 10:02:58
Build version: 16.05. 4.10.02.58

17:05:53: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --reset
************************************************

17:05:53: INFO: Current working dir (cwd): C:\ND1_BootFix\
17:05:53: INFO: Showing network mappings to allow debugging
17:05:53: INFO: User wants to talk to port '\\.\COM9'
17:05:53: INFO: Took 0.21900000 seconds to open port
17:05:53: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
17:05:53: INFO: If you don't want this, use --dontsorttags

17:05:53: INFO: Sending <configure>


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


17:06:19: {ERROR: Could not write to '\\.\COM9', Windows API WriteFile failed! Your device is probably *not* on this port, attempted 100 times}

Writing log to 'C:\ND1_BootFix\port_trace.txt', might take a minute


Log is 'C:\ND1_BootFix\port_trace.txt'



Press any key to exit


Done
Для продолжения нажмите любую клавишу . . .
лог из файла port_trace.txt

17:05:53: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
fh_loader.exe --port=\\.\COM9 --reset
************************************************

17:05:53: DEBUG: Binary build date: May 4 2016 @ 10:02:58

17:05:53: DEBUG: Build Version: 16.05. 4.10.02.58

17:05:53: INFO: Current working dir (cwd): C:\ND1_BootFix\
17:05:53: INFO: Showing network mappings to allow debugging
17:05:53: DEBUG: Новые подключения будут запомнены.

17:05:53: DEBUG:

17:05:53: DEBUG: В списке нет элементов.

17:05:53: DEBUG:

17:05:53: INFO: User wants to talk to port '\\.\COM9'
17:05:53: DEBUG: port_fd=0xE0

17:05:53: INFO: Took 0.21900000 seconds to open port
17:05:53: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
17:05:53: INFO: If you don't want this, use --dontsorttags

17:05:53: INFO: Sending <configure>
17:05:53: DEBUG: CHANNEL DATA (P0000) (H00202) ( 246 bytes) - HOST TO TARGET -->
===========================================================================================================
<?xml version="1.0" encoding="UTF-8" ?>
<data>
<configure MemoryName="eMMC" Verbose="0" AlwaysValidate="0" MaxDigestTableSizeInBytes="8192" MaxPayloadSizeToTargetInBytes="1048576" ZlpAwareHost="1" SkipStorageInit="0" TargetName="8960" />
</data>

============================================================================================================

17:05:53: DEBUG: Only 0 bytes written of 246 requested, attempt 1 of 100
17:05:54: DEBUG: Only 0 bytes written of 246 requested, attempt 2 of 100
17:05:54: DEBUG: Only 0 bytes written of 246 requested, attempt 3 of 100
17:05:54: DEBUG: Only 0 bytes written of 246 requested, attempt 4 of 100
17:05:54: DEBUG: Only 0 bytes written of 246 requested, attempt 5 of 100
17:05:55: DEBUG: Only 0 bytes written of 246 requested, attempt 6 of 100
17:05:55: DEBUG: Only 0 bytes written of 246 requested, attempt 7 of 100
17:05:55: DEBUG: Only 0 bytes written of 246 requested, attempt 8 of 100
17:05:55: DEBUG: Only 0 bytes written of 246 requested, attempt 9 of 100
17:05:56: DEBUG: Only 0 bytes written of 246 requested, attempt 10 of 100
17:05:56: DEBUG: Only 0 bytes written of 246 requested, attempt 11 of 100
17:05:56: DEBUG: Only 0 bytes written of 246 requested, attempt 12 of 100
17:05:56: DEBUG: Only 0 bytes written of 246 requested, attempt 13 of 100
17:05:57: DEBUG: Only 0 bytes written of 246 requested, attempt 14 of 100
17:05:57: DEBUG: Only 0 bytes written of 246 requested, attempt 15 of 100
17:05:57: DEBUG: Only 0 bytes written of 246 requested, attempt 16 of 100
17:05:57: DEBUG: Only 0 bytes written of 246 requested, attempt 17 of 100
17:05:58: DEBUG: Only 0 bytes written of 246 requested, attempt 18 of 100
17:05:58: DEBUG: Only 0 bytes written of 246 requested, attempt 19 of 100
17:05:58: DEBUG: Only 0 bytes written of 246 requested, attempt 20 of 100
17:05:58: DEBUG: Only 0 bytes written of 246 requested, attempt 21 of 100
17:05:59: DEBUG: Only 0 bytes written of 246 requested, attempt 22 of 100
17:05:59: DEBUG: Only 0 bytes written of 246 requested, attempt 23 of 100
17:05:59: DEBUG: Only 0 bytes written of 246 requested, attempt 24 of 100
17:05:59: DEBUG: Only 0 bytes written of 246 requested, attempt 25 of 100
17:06:00: DEBUG: Only 0 bytes written of 246 requested, attempt 26 of 100
17:06:00: DEBUG: Only 0 bytes written of 246 requested, attempt 27 of 100
17:06:00: DEBUG: Only 0 bytes written of 246 requested, attempt 28 of 100
17:06:00: DEBUG: Only 0 bytes written of 246 requested, attempt 29 of 100
17:06:01: DEBUG: Only 0 bytes written of 246 requested, attempt 30 of 100
17:06:01: DEBUG: Only 0 bytes written of 246 requested, attempt 31 of 100
17:06:01: DEBUG: Only 0 bytes written of 246 requested, attempt 32 of 100
17:06:01: DEBUG: Only 0 bytes written of 246 requested, attempt 33 of 100
17:06:02: DEBUG: Only 0 bytes written of 246 requested, attempt 34 of 100
17:06:02: DEBUG: Only 0 bytes written of 246 requested, attempt 35 of 100
17:06:02: DEBUG: Only 0 bytes written of 246 requested, attempt 36 of 100
17:06:02: DEBUG: Only 0 bytes written of 246 requested, attempt 37 of 100
17:06:03: DEBUG: Only 0 bytes written of 246 requested, attempt 38 of 100
17:06:03: DEBUG: Only 0 bytes written of 246 requested, attempt 39 of 100
17:06:03: DEBUG: Only 0 bytes written of 246 requested, attempt 40 of 100
17:06:04: DEBUG: Only 0 bytes written of 246 requested, attempt 41 of 100
17:06:04: DEBUG: Only 0 bytes written of 246 requested, attempt 42 of 100
17:06:04: DEBUG: Only 0 bytes written of 246 requested, attempt 43 of 100
17:06:04: DEBUG: Only 0 bytes written of 246 requested, attempt 44 of 100
17:06:05: DEBUG: Only 0 bytes written of 246 requested, attempt 45 of 100
17:06:05: DEBUG: Only 0 bytes written of 246 requested, attempt 46 of 100
17:06:05: DEBUG: Only 0 bytes written of 246 requested, attempt 47 of 100
17:06:05: DEBUG: Only 0 bytes written of 246 requested, attempt 48 of 100
17:06:06: DEBUG: Only 0 bytes written of 246 requested, attempt 49 of 100
17:06:06: DEBUG: Only 0 bytes written of 246 requested, attempt 50 of 100
17:06:06: DEBUG: Only 0 bytes written of 246 requested, attempt 51 of 100
17:06:06: DEBUG: Only 0 bytes written of 246 requested, attempt 52 of 100
17:06:07: DEBUG: Only 0 bytes written of 246 requested, attempt 53 of 100
17:06:07: DEBUG: Only 0 bytes written of 246 requested, attempt 54 of 100
17:06:07: DEBUG: Only 0 bytes written of 246 requested, attempt 55 of 100
17:06:07: DEBUG: Only 0 bytes written of 246 requested, attempt 56 of 100
17:06:08: DEBUG: Only 0 bytes written of 246 requested, attempt 57 of 100
17:06:08: DEBUG: Only 0 bytes written of 246 requested, attempt 58 of 100
17:06:08: DEBUG: Only 0 bytes written of 246 requested, attempt 59 of 100
17:06:08: DEBUG: Only 0 bytes written of 246 requested, attempt 60 of 100
17:06:09: DEBUG: Only 0 bytes written of 246 requested, attempt 61 of 100
17:06:09: DEBUG: Only 0 bytes written of 246 requested, attempt 62 of 100
17:06:09: DEBUG: Only 0 bytes written of 246 requested, attempt 63 of 100
17:06:09: DEBUG: Only 0 bytes written of 246 requested, attempt 64 of 100
17:06:10: DEBUG: Only 0 bytes written of 246 requested, attempt 65 of 100
17:06:10: DEBUG: Only 0 bytes written of 246 requested, attempt 66 of 100
17:06:10: DEBUG: Only 0 bytes written of 246 requested, attempt 67 of 100
17:06:10: DEBUG: Only 0 bytes written of 246 requested, attempt 68 of 100
17:06:11: DEBUG: Only 0 bytes written of 246 requested, attempt 69 of 100
17:06:11: DEBUG: Only 0 bytes written of 246 requested, attempt 70 of 100
17:06:11: DEBUG: Only 0 bytes written of 246 requested, attempt 71 of 100
17:06:11: DEBUG: Only 0 bytes written of 246 requested, attempt 72 of 100
17:06:12: DEBUG: Only 0 bytes written of 246 requested, attempt 73 of 100
17:06:12: DEBUG: Only 0 bytes written of 246 requested, attempt 74 of 100
17:06:12: DEBUG: Only 0 bytes written of 246 requested, attempt 75 of 100
17:06:13: DEBUG: Only 0 bytes written of 246 requested, attempt 76 of 100
17:06:13: DEBUG: Only 0 bytes written of 246 requested, attempt 77 of 100
17:06:13: DEBUG: Only 0 bytes written of 246 requested, attempt 78 of 100
17:06:13: DEBUG: Only 0 bytes written of 246 requested, attempt 79 of 100
17:06:14: DEBUG: Only 0 bytes written of 246 requested, attempt 80 of 100
17:06:14: DEBUG: Only 0 bytes written of 246 requested, attempt 81 of 100
17:06:14: DEBUG: Only 0 bytes written of 246 requested, attempt 82 of 100
17:06:14: DEBUG: Only 0 bytes written of 246 requested, attempt 83 of 100
17:06:15: DEBUG: Only 0 bytes written of 246 requested, attempt 84 of 100
17:06:15: DEBUG: Only 0 bytes written of 246 requested, attempt 85 of 100
17:06:15: DEBUG: Only 0 bytes written of 246 requested, attempt 86 of 100
17:06:15: DEBUG: Only 0 bytes written of 246 requested, attempt 87 of 100
17:06:16: DEBUG: Only 0 bytes written of 246 requested, attempt 88 of 100
17:06:16: DEBUG: Only 0 bytes written of 246 requested, attempt 89 of 100
17:06:16: DEBUG: Only 0 bytes written of 246 requested, attempt 90 of 100
17:06:16: DEBUG: Only 0 bytes written of 246 requested, attempt 91 of 100
17:06:17: DEBUG: Only 0 bytes written of 246 requested, attempt 92 of 100
17:06:17: DEBUG: Only 0 bytes written of 246 requested, attempt 93 of 100
17:06:17: DEBUG: Only 0 bytes written of 246 requested, attempt 94 of 100
17:06:17: DEBUG: Only 0 bytes written of 246 requested, attempt 95 of 100
17:06:18: DEBUG: Only 0 bytes written of 246 requested, attempt 96 of 100
17:06:18: DEBUG: Only 0 bytes written of 246 requested, attempt 97 of 100
17:06:18: DEBUG: Only 0 bytes written of 246 requested, attempt 98 of 100
17:06:18: DEBUG: Only 0 bytes written of 246 requested, attempt 99 of 100
17:06:19: DEBUG: Only 0 bytes written of 246 requested, attempt 100 of 100


_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|


17:06:19: {ERROR: WritePort:3976 Could not write to '\\.\COM9', Windows API WriteFile failed! Your device is probably *not* on this port, attempted 100 times

the_laser
25.04.2019, 21:58
все выглядит так, что после загрузчика аппарат просто перегружается.
вероятно, не может что-то инициализировать в телефоне и выпадает в критическое исключение.
вполне возможно, это проблема с eMMC

tomash777
26.04.2019, 15:31
флешка умерла
лог z3x
Setting frequence to 21 Mhz
CMD Pullup Level: 3207 mV
CMD Active Level: 3248 mV
EMMC Device Information :
EMMC CID: 0600003136FFFFFFFFFF195C493934EA
EMMC CSD: 8C4F012A0F598000F6D801E08A400076
EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF
EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2001
EMMC ROM 1 (Main User Data) Capacity: 0 MB (000000002000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: Yes
Extended CSD Information :
Extended CSD rev: 1.0 (MMC 4.0)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x00
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 16_195C4939_20190426_130750.extcsd
EMMC Init completed.

Error: EMMC Password Locked

попытка сделать формат
Operation: Universal Factory Format
Please, wait ...

Critical error: Access violation at address 00008000 in module 'eMMC_tool.exe'. Read of address 00008000.

Radiotrance
22.05.2019, 16:02
eMMC заменить не получилось. 900E.

Судя по логу EasyJTAG, в теле используется RPMB.

the_laser
22.05.2019, 20:09
eMMC заменить не получилось. 900E.

Судя по логу EasyJTAG, в теле используется RPMB.

лечи 900e скриптом ...

XXXNEXTXXX
30.05.2019, 17:06
Как его шить то блин не видит программа телефон ни в edl ни в dowloand mode на счету 10 кредитов
использую версию 0.049 на скиншоте другая

the_laser
30.05.2019, 20:15
NTool EDL режим не поддерживает, а для нормального fastboot необходимо использовать драйвера из папки drivers, предварительно удалить существующие.

alonetops
13.07.2019, 15:37
TA-1021 не входит в edl хочу frp скинуть octoplus боксом все перепробовал есть кабель edl универсальный 910ком не помогает вставляю кабель включается на зарядку! Подскажите кто знает как ввести?

dervish
14.07.2019, 13:20
Каким боком здесь octoplus ? Вы разделом ошиблись.

Siecker
24.07.2019, 00:43
ta-1021 память заблокировалась в режиме чтения. С нее был слит дамп 1GB т.е. все до раздела system. Залито в новую. При подключению к компу 9008. После бутфикса 900e, Повторяю процедуру через ТП, 900e остается.
И да, использует RPMB проц. Все конец в оживлении бута?
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 9686 , Response: Not Clean
Лог load_fh.cmd

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 00000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: -1 physical_partition_number: 0 filename: DISK value: 0 crc_size 9
2
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-1,
92)" what="Update Backup Header with CRC of Backup Header."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
59, over bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with B57B0136" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
Status: 0 The operation completed successfully.


C:\adb\PLE_D1C_ND1_BootFix>emmcdl.exe -p COM7 -f D1C-0-3700-prog_emmc_firehose_8
937_lite.mbn -x PLE-0-3140-patch0.xml
Version 2.10
PblHack: Error - 1836597052
Did not receive Sahara hello packet from device

!!!!!!!! WARNING: Flash programmer failed to load trying to continue !!!!!!!!!

.0" encoding="UTF-8" ?><data><log value="XML (0 bytes) not validated" /></data><
?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" /></data>
Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="1048576"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Host's payload to targe
t size is too large" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

---Target returned NAK---

We are decreasing our max packet size 16384


Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="16384"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
Connected to flash programmer, starting download
start_sector: 17 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 start_sector: 17 physical_partition_number: 0 fi
lename: DISK value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_I
N_BYTES="512" byte_offset="296" filename="DISK" physical_partition_number="0" si
ze_in_bytes="8" start_sector="17" value="NUM_DISK_SECTORS-34" what="Update last
partition 63 'userdata' with actual size in Primary Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 17 with
03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 15 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 start_sector: -18 physical_partition_number: 0 f
ilename: DISK value: -34 crc_size -858993460
patch_offset: 296 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_I
N_BYTES="512" byte_offset="296" filename="DISK" physical_partition_number="0" si
ze_in_bytes="8" start_sector="NUM_DISK_SECTORS-18" value="NUM_DISK_SECTORS-34" w
hat="Update last partition 63 'userdata' with actual size in Backup Header."/></
data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071342
with 03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 start_sector: 1 physical_partition_number: 0 file
name: DISK value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="48" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="1" value="NUM_DISK_SECTORS-34" what="Update Primary
Header with LastUseableLBA"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
3A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -34 crc_size -858993460
patch_offset: 48 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="48" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-34" what
="Update Backup Header with LastUseableLBA."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFDE" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: -1 crc_size -858993460
patch_offset: 32 patch_size: 8 start_sector: 1 physical_partition_number: 0 file
name: DISK value: -1 crc_size -858993460
patch_offset: 32 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="32" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="1" value="NUM_DISK_SECTORS-1" what="Update Primary H
eader with BackupGPT Header Location"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
3A3DFFF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -1 crc_size -858993460
patch_offset: 24 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -1 crc_size -858993460
patch_offset: 24 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="24" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-1" what=
"Update Backup Header with CurrentLBA."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFFF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: -33 crc_size -858993460
patch_offset: 72 patch_size: 8 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: -33 crc_size -858993460
patch_offset: 72 patch_size: 8 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="72" filename="DISK" physical_partition_number="0" size
_in_bytes="8" start_sector="NUM_DISK_SECTORS-1" value="NUM_DISK_SECTORS-33" what
="Update Backup Header with Partition Array Location"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03A3DFDF" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: DISK value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="88" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="CRC32(2,8192)" what="Update Primary Header
with CRC of Partition Array"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 2, ove
r bytes 8192" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 3
9FCAFAD" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: 0 crc_size 8192
patch_offset: 88 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="88" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-33
,8192)" what="Update Backup Header with CRC of Partition Array."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
27, over bytes 8192" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 03921AC9" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: PLE-0-3140-gpt_main0.bin
value: 0 crc_size 8192
patch_offset: 16 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: PLE-0-3140-gpt_main0.bin value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: 1 physical_partition_number: 0 file
name: DISK value: 0 crc_size 92
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="0" what="Zero Out Header CRC in Primary He
ader"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 0
0000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 1 physical_partition_number: 0 filename: DISK value: 0 crc_size 92

patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="1" value="CRC32(1,92)" what="Update Primary Header w
ith CRC of Primary Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 1, ove
r bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 1 with 6
4BB2881" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: 32 physical_partition_number: 0 filename: PLE-0-3140-gpt_backup0.b
in value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: 32 physical_partition_number: 0 fil
ename: PLE-0-3140-gpt_backup0.bin value: 0 crc_size 92
patch_offset: 16 patch_size: 4 start_sector: -1 physical_partition_number: 0 fil
ename: DISK value: 0 crc_size 92
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="0" what="Zero Out Header
CRC in Backup Header"/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with 00000000" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
start_sector: -1 physical_partition_number: 0 filename: DISK value: 0 crc_size 9
2
patch_offset: 16 patch_size: 4 <?xml version="1.0" ?><data><patch SECTOR_SIZE_IN
_BYTES="512" byte_offset="16" filename="DISK" physical_partition_number="0" size
_in_bytes="4" start_sector="NUM_DISK_SECTORS-1" value="CRC32(NUM_DISK_SECTORS-1,
92)" what="Update Backup Header with CRC of Backup Header."/></data>

<?xml version="1.0" encoding="UTF-8" ?><data><log value="crc start sector 610713
59, over bytes 92" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Patched sector 61071359
with B57B0136" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>
Status: 0 The operation completed successfully.


C:\adb\PLE_D1C_ND1_BootFix>emmcdl.exe -p COM7 -f D1C-0-3700-prog_emmc_firehose_8
937_lite.mbn -r
Version 2.10
PblHack: Error - 1836597052
Did not receive Sahara hello packet from device

!!!!!!!! WARNING: Flash programmer failed to load trying to continue !!!!!!!!!

.0" encoding="UTF-8" ?><data><log value="XML (0 bytes) not validated" /></data><
?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" /></data>
Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="1048576"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="Host's payload to targe
t size is too large" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="NAK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

---Target returned NAK---

We are decreasing our max packet size 16384


Programming device using SECTOR_SIZE=512

<?xml version = "1.0" ?><data><configure MemoryName="emmc" ZLPAwareHost="1" Skip
StorageInit="0" SkipWrite="0" MaxPayloadSizeToTargetInBytes="16384"/></data>
<?xml version="1.0" encoding="UTF-8" ?><data><log value="[email protected] [email protected]
0806D810" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" MinVersionSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>
Connected to flash programmer, starting download
Programming RAW command: <?xml version="1.0" ?><data><power value="reset" /></da
ta>


<?xml version="1.0" encoding="UTF-8" ?><data><response value="ACK" /></data>nSup
ported="1" MemoryName="eMMC" MaxPayloadSizeFromTargetInBytes="4096" MaxPayloadSi
zeToTargetInBytes="16384" MaxPayloadSizeToTargetInBytesSupported="16384" MaxXMLS
izeInBytes="4096" Version="1" TargetName="8937" /></data>

Status: 0 The operation completed successfully.

Для продолжения нажмите любую клавишу . . .

C:\adb\PLE_D1C_ND1_BootFix>if "1" == "0" echo WARNING: Could not find any connec
ted Qualcomm HS-USB QDLoader 9008.

C:\adb\PLE_D1C_ND1_BootFix>echo.


C:\adb\PLE_D1C_ND1_BootFix>endlocal

C:\adb\PLE_D1C_ND1_BootFix>pause
Для продолжения нажмите любую клавишу . . .

C:\adb\PLE_D1C_ND1_BootFix>goto :EOF

C:\adb\PLE_D1C_ND1_BootFix>

the_laser
24.07.2019, 17:13
не увидел прошивки бута.
два файла прошивается, rawprgram и patch
увидел только патч тут.

с поддержки скачай бутфикс.

Siecker
25.07.2019, 15:13
бут фикс взял вначале темы. Доступа нет скачать, покупка кредитов не доступна ( uo5oq gsmserver.ru imei-server.ru )

https://support.ntool.info/resellers.php = Resellers list

Unable to connect to DB :

Supercontick
22.11.2019, 02:02
Здравствуйте. Ребята, расскажите пожалуйста. А то пять страниц перечитал, но так и не понял, возможно ли заменить память?! Какая подходит? KMRX1000BM-B614 на этой emmc есть вариант поднять тело, если она с другого аппарата где стоит такой же проц(но он зараза в КЗ).

himik230782
07.03.2020, 00:25
Есть решение по замене EMMC? Аппарат на последних пока живет, но память явно дохнет.

Supercontick
10.03.2020, 17:59
Взял плату от Lenovo K6 note K53a48, там как раз такой же проц стоит и память в паре - KMRX1000BM- B614. После установки, при подключении USB шнурка, аппарат издает вибро и начинает нормально заряжаться, даже через некоторое время появляется MTP устройство на ПК. Но если прошивать прошивку от Nokia через любую программу в режиме EDL, даже через BEST2, шлет с ошибкой " Pickup loader from firmware package
FH_LOAD_CODE : 14"
Пробовал через Иксы залить дамп с родной памяти, такая же история. Подскажите пожалуйста, какой загрузчик или каике файлы можно подменить? А может есть какое то решение при прошивке?

И так, что еще предпринял: Решил рискнуть и изменить CID во флешке KMRX1000BM- B614 на CID от H9TQ26ADFTBC (родная). И тут меня ждало не понятие: CID не меняется, ни в какую. ПОЧЕМУ?