Показано с 1 по 4 из 4

Тема: cruiser

  1. #1
    Member
    Регистрация
    01.07.2009
    Адрес
    Нижний Новгород
    Сообщений
    132
    Спасибо
    5
    Благодарностей: 1 : 1

    cruiser

    хочу купить cruiser.не подскажете он gdfs восстанавливает на db2020 без логов и тп???

  2. #2
    Senior Member
    Регистрация
    23.06.2008
    Адрес
    Барнаул
    Сообщений
    1,161
    Спасибо
    76
    Благодарностей: 403 : 180
    Только за логи, ТП вобще нет.

  3. #3
    Senior Member Аватар для kmips
    Регистрация
    18.02.2005
    Адрес
    11CC8
    Сообщений
    802
    Спасибо
    336
    Благодарностей: 364 : 112
    Цитата Сообщение от Rtehnik Посмотреть сообщение
    Только за логи, ТП вобще нет.
    Да ну???
    SE Testpoint Full Unlocker





    Cruiser Suite SE Testpoint Full Unlocker requires a new Cruiser UC20 cable.


    Unlocking procedure - DB2010

    1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
    2. Choose the phone model.
    3. Connect the data cable and power supply clips to the phone.
    4. Double-click on the appropriate cruiser UC20 serial cable.
    5. Wait until the program asks you to connect the Testpoint Stage 2.
    6. Connect the testpoint needle to testpoint pin 37.
    7. Program plays a sound when the testpoint connection is detected.
    8. Hold the testpoint until the application informs that the testpoint can be released
    (it plays the second sound).
    9. Wait until program performs all operations.
    10. Phone is recovered and unlocked, disconnect the cabling from the phone.

    Recovery mode

    As far as the EROM is overwritten during the unlock, a broken communication during flashing of EROM
    might make the phone temporarily unusable. At that time it's required to proceed the recovery:

    1. Choose the option "Skip testpoint stage 1 / Recovery mode"
    2. Double-click on the appropriate cruiser UC20 serial cable.
    3. Wait until the program asks you to connect the Testpoint Stage 2.
    4. Connect the testpoint needle to testpoint pin 37.
    5. Program plays a sound when the testpoint connection is detected.
    6. Hold the testpoint until the application informs that the testpoint can be released
    (it plays the second sound).
    7. Wait until program performs all operations.
    8. Phone is recovered and unlocked, disconnect the cabling from the phone.


    Unlocking procedure - DB2012

    1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
    2. Choose the phone model.
    3. Connect the data cable and power supply clips to the phone.
    4. Double-click on the appropriate cruiser UC20 serial cable.
    5. Wait until the program asks you to connect the Testpoint Stage 1.
    6. Connect the testpoint needle to testpoint pin 27.
    7. Program plays a sound when the testpoint connection is detected.
    8. Hold the testpoint until the application informs that the testpoint can be released
    (it plays the second sound).
    9. Wait until program performs all operations.
    10. Phone is unlocked, disconnect the cabling from the phone.

    Recovery mode

    As far as the EROM is overwritten during the unlock, a broken communication during flashing of EROM
    might make the phone temporarily unusable. At that time it's required to proceed the recovery:

    1. Choose the option "Skip testpoint stage 1 / Recovery mode"
    2. Double-click on the appropriate cruiser UC20 serial cable.
    3. Wait until the program asks you to connect the Testpoint Stage 2.
    4. Connect the testpoint needle to testpoint pin 37.
    5. Program plays a sound when the testpoint connection is detected.
    6. Hold the testpoint until the application informs that the testpoint can be released
    (it plays the second sound).
    7. Wait until program performs all operations.
    8. Phone is recovered and unlocked, disconnect the cabling from the phone.



    Unlocking procedure - DB2020

    1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
    2. Choose the phone model.
    3. Connect the data cable and power supply clips to the phone.
    4. If you want to skip Testpoint Stage 1, select the appropriate option
    5. Double-click on the appropriate cruiser UC20 serial cable.

    Stage 1

    1. Wait until the program asks you to connect the Testpoint Stage 1.
    2. Connect the testpoint needle to testpoint pin (stage 1).
    3. Program plays a sound when the testpoint connection is detected.
    4. Hold the testpoint until the application informs that the testpoint can be released
    (it plays the second sound)
    5. Wait until program performs operations and continues to stage 2.

    Note: Once the Stage 1 completes correctly, there is no need to repeat it anymore.

    Stage 2

    1. Connect the testpoint needle to testpoint pin stage 2 (The program asks you to do so)
    2. Program plays a sound when the testpoint connection is detected.
    3. Hold the testpoint for about 4 seconds, until the application informs that the testpoint can be released
    (it plays the second sound)
    5. Wait until program performs operations finishes.
    6. Phone is unlocked, disconnect the cabling from the phone.

    Но SE_Tool рулит лучше!

  4. #4
    Senior Member
    Регистрация
    23.06.2008
    Адрес
    Барнаул
    Сообщений
    1,161
    Спасибо
    76
    Благодарностей: 403 : 180
    Тогда извиняюсь, значит у меня устаревшая информация, уже года полтора к компу не подключал, на полочке пылится.

Похожие темы

  1. Cruiser 5 in 1
    от zeruton в разделе SonyEricsson для новичков
    Ответов: 0
    Последний ответ: 05.06.2009, 17:28
  2. cruiser!!!
    от chevron в разделе Остальное оборудование
    Ответов: 5
    Последний ответ: 27.11.2007, 01:13
  3. Cruiser V6.0
    от GEORGIA в разделе SE Software и Firmware
    Ответов: 4
    Последний ответ: 30.10.2005, 15:41

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •  
  Рейтинг@Mail.ru