хочу купить cruiser.не подскажете он gdfs восстанавливает на db2020 без логов и тп???
хочу купить cruiser.не подскажете он gdfs восстанавливает на db2020 без логов и тп???
Только за логи, ТП вобще нет.
Да ну???
SE Testpoint Full Unlocker
Cruiser Suite SE Testpoint Full Unlocker requires a new Cruiser UC20 cable.
Unlocking procedure - DB2010
1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
2. Choose the phone model.
3. Connect the data cable and power supply clips to the phone.
4. Double-click on the appropriate cruiser UC20 serial cable.
5. Wait until the program asks you to connect the Testpoint Stage 2.
6. Connect the testpoint needle to testpoint pin 37.
7. Program plays a sound when the testpoint connection is detected.
8. Hold the testpoint until the application informs that the testpoint can be released
(it plays the second sound).
9. Wait until program performs all operations.
10. Phone is recovered and unlocked, disconnect the cabling from the phone.
Recovery mode
As far as the EROM is overwritten during the unlock, a broken communication during flashing of EROM
might make the phone temporarily unusable. At that time it's required to proceed the recovery:
1. Choose the option "Skip testpoint stage 1 / Recovery mode"
2. Double-click on the appropriate cruiser UC20 serial cable.
3. Wait until the program asks you to connect the Testpoint Stage 2.
4. Connect the testpoint needle to testpoint pin 37.
5. Program plays a sound when the testpoint connection is detected.
6. Hold the testpoint until the application informs that the testpoint can be released
(it plays the second sound).
7. Wait until program performs all operations.
8. Phone is recovered and unlocked, disconnect the cabling from the phone.
Unlocking procedure - DB2012
1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
2. Choose the phone model.
3. Connect the data cable and power supply clips to the phone.
4. Double-click on the appropriate cruiser UC20 serial cable.
5. Wait until the program asks you to connect the Testpoint Stage 1.
6. Connect the testpoint needle to testpoint pin 27.
7. Program plays a sound when the testpoint connection is detected.
8. Hold the testpoint until the application informs that the testpoint can be released
(it plays the second sound).
9. Wait until program performs all operations.
10. Phone is unlocked, disconnect the cabling from the phone.
Recovery mode
As far as the EROM is overwritten during the unlock, a broken communication during flashing of EROM
might make the phone temporarily unusable. At that time it's required to proceed the recovery:
1. Choose the option "Skip testpoint stage 1 / Recovery mode"
2. Double-click on the appropriate cruiser UC20 serial cable.
3. Wait until the program asks you to connect the Testpoint Stage 2.
4. Connect the testpoint needle to testpoint pin 37.
5. Program plays a sound when the testpoint connection is detected.
6. Hold the testpoint until the application informs that the testpoint can be released
(it plays the second sound).
7. Wait until program performs all operations.
8. Phone is recovered and unlocked, disconnect the cabling from the phone.
Unlocking procedure - DB2020
1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
2. Choose the phone model.
3. Connect the data cable and power supply clips to the phone.
4. If you want to skip Testpoint Stage 1, select the appropriate option
5. Double-click on the appropriate cruiser UC20 serial cable.
Stage 1
1. Wait until the program asks you to connect the Testpoint Stage 1.
2. Connect the testpoint needle to testpoint pin (stage 1).
3. Program plays a sound when the testpoint connection is detected.
4. Hold the testpoint until the application informs that the testpoint can be released
(it plays the second sound)
5. Wait until program performs operations and continues to stage 2.
Note: Once the Stage 1 completes correctly, there is no need to repeat it anymore.
Stage 2
1. Connect the testpoint needle to testpoint pin stage 2 (The program asks you to do so)
2. Program plays a sound when the testpoint connection is detected.
3. Hold the testpoint for about 4 seconds, until the application informs that the testpoint can be released
(it plays the second sound)
5. Wait until program performs operations finishes.
6. Phone is unlocked, disconnect the cabling from the phone.
Но SE_Tool рулит лучше!
Тогда извиняюсь, значит у меня устаревшая информация, уже года полтора к компу не подключал, на полочке пылится.