Показано с 1 по 10 из 10

Тема: n97 после неудачного обновления ПО.

  1. #1
    Member
    Регистрация
    17.07.2005
    Адрес
    Москва-Волгодонск
    Сообщений
    154
    Спасибо
    4
    Благодарностей: 24 : 5

    n97 после неудачного обновления ПО.

    принесли его, пытались прошить дома джафом, теперь когда нажимаешь на кнопку вкл. только вибра и все. я его ЮФС-ом прошил(22-й версией) он не ожил, есть еще циклон, им я тоже его прошил и не алле....говорят что циклон много что умеет, помогите в нем разобраться что куда тыкать и подставлять.

  2. #2
    Member Аватар для babycry
    Регистрация
    12.08.2006
    Адрес
    Красный Луч, ЛНР
    Сообщений
    451
    Спасибо
    54
    Благодарностей: 236 : 100
    Для чего понадобилось шить? N97 RM- какой? Логи где? С таким количеством информации может быть все-таки вам лучше обратиться на "Битву экстрасенсов"?

    P.S. Cyclone действительно много чего умеет. В умелых руках и х@й - молоток.

  3. #3
    Member
    Регистрация
    17.07.2005
    Адрес
    Москва-Волгодонск
    Сообщений
    154
    Спасибо
    4
    Благодарностей: 24 : 5
    rm-505 для чего его шили не сказали..
    вот лог прошивки циклона


    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    APE Boot skipped on user request
    Flashbus Write baud set to 5.0Mbits
    Restarting MCU...
    Processing pre flash tasks...
    Backing up RPL...
    RPL Creation started...
    Processing CMT Part...
    Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    APE Subsystem Not Found
    Flashbus Write baud set to 5.0Mbits
    Storing NPC...
    Storing CCC...
    Storing HWC...
    CMT VARIANT Not Found
    Restarting MCU...
    RPL Saved OK
    RPL backup thread finished, continuing...
    Backing up simlock...
    Simlock backup problem -> Phone not detected
    Backup simlock thread finished, continuing...
    Pre flash tasks finished, continuing...
    Processing RM-505_22.0.110_prd.core.C00 (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    RM-505_22.0.110_prd.core.C00, Type: Flash Image, Algo: XSR 1.5, BB5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    Flashbus Write baud set to 5.0Mbits
    Sending Certificates...
    Certificates OK
    Partitioning...
    Partitioning OK
    Started group flash erase
    EraseArea[0,CMT]: 0x00040000-0x00082FFF, ONENAND
    EraseArea[0,CMT]: 0x00083400-0x003FFFFF, ONENAND
    EraseArea[0,CMT]: 0x00800000-0x00D5FFFF, ONENAND
    EraseArea[0,CMT]: 0x00D60000-0x0AB9FFFF, ONENAND
    Erase Partition (CMT)
    Waiting 320s for erasure finish...
    Erase taken 0.969s
    Writing all blocks...
    Writing CMT ADA Certificate...
    Writing CMT KEYS Certificate...
    Writing CMT PRIMAPP Certificate...
    Writing CMT RAP3NAND Certificate...
    Writing CMT PASUBTOC Certificate...
    Writing CMT PAPUBKEYS Certificate...
    Writing CMT SOS*UPDAPP Certificate...
    Writing CMT SOS*DSP0 Certificate...
    Writing CMT SOS*ISASW Certificate...
    Writing CMT SOS+CORE Certificate...
    Writing CMT SOS+ROFS1 Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 121.672s
    Flashing Speed: 7331,72 kBit/S
    Restarting MCU...
    Processing RM-505_22.0.110_prd.core.C00 (APE)...
    Processing RM-505_22.0.110_prd.rofs2.V11 (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    RM-505_22.0.110_prd.rofs2.V11, Type: Flash Image, Algo: XSR 1.5, BB5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x079A0000-0x09C9FFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.203s
    Writing all blocks...
    Writing CMT SOS+ROFS2 Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 25.485s
    Flashing Speed: 7161,97 kBit/S
    Restarting MCU...
    Processing RM-505_22.0.110_prd.rofs2.V11 (APE)...
    Processing RM-505_22.0.110_C01_prd.rofs3.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    RM-505_22.0.110_C01_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.5, BB5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x09CA0000-0x0AB9FFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.109s
    Writing all blocks...
    Writing CMT SOS+ROFS3 Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 0.94s
    Flashing Speed: 785,36 kBit/S
    Restarting MCU...
    Processing RM-505_22.0.110_C01_prd.rofs3.fpsx (APE)...
    Processing RM505_507_22.0.110_uda_3_001.uda.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    RM505_507_22.0.110_uda_3_001.uda.fpsx, Type: Flash Image, Algo: XSR 1.5, BB5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    Flashbus Write baud set to 5.0Mbits
    Started group flash erase
    EraseArea[0,CMT]: 0x0ABA0000-0x0F71FFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.422s
    Writing all blocks...
    Programming Status OK!
    All blocks written OK! Time taken 11.172s
    Flashing Speed: 6600,03 kBit/S
    Restarting MCU...
    Processing RM505_507_22.0.110_uda_3_001.uda.fpsx (APE)...
    Processing RM505_APE_ONLY_ENO_09w23_v0.072.fpsx (CMT)...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1990000FE9DA0158FBF8E0A77FE3C6641E800620
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    RM505_APE_ONLY_ENO_09w23_v0.072.fpsx, Type: Flash Image, Algo: XSR 1.5, BB5
    Searching for BootCode: DualLine 32Bit
    RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.16.2, Algo: BB5
    Flashbus Write baud set to 650Kbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
    RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.22.0, Algo: XSR 1.5
    Writing CMT PASUBTOC Certificate...
    Writing CMT ALG Certificate...
    CMT Algorithm Ready!
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Adding FUR Client (CMT, State: Ready)...
    CMT FUR Ready!
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    PAPUBKEYS Hash for CMT: DAEF2C397A3F8FC5CA8B1F429D73C94C4A25B15B
    Flashbus Write baud set to 5.0Mbits
    Sending Certificates...
    Certificates OK
    Started group flash erase
    EraseArea[0,CMT]: 0x00400000-0x007FFFFF, ONENAND
    Waiting 320s for erasure finish...
    Erase taken 0.47s
    Writing all blocks...
    Writing CMT SOS*ENO Certificate...
    Programming Status OK!
    All blocks written OK! Time taken 3.281s
    Flashing Speed: 7030,37 kBit/S
    Restarting MCU...
    Processing RM505_APE_ONLY_ENO_09w23_v0.072.fpsx (APE)...
    All images processed OK! Processing post flash tasks...
    Setting Factory Defaults...
    Factory defaults OK
    Reading info...
    Failed to read info -> Phone not detected
    Read info thread finished, continuing...
    Post flash tasks finished!
    Flashing successfully finished!

  4. #4
    Member
    Регистрация
    16.06.2008
    Адрес
    Казань
    Сообщений
    221
    Спасибо
    218
    Благодарностей: 58 : 14
    [Цитата = Ventil11; 1832048] принесли его, пытались прошить дома джафом, теперь когда нажимаешь на кнопку вкл. только вибра и все. я его ЮФС-ом прошил (22-й версией) он не ожил, есть еще циклон, им я тоже его прошил и не алле .... говорят что циклон много что умеет, помогите в нем разобраться что куда тыкать и подставлять. [ / quote]

    PHOENIXом попробуй по dead usb прошить

  5. #5
    Member
    Регистрация
    17.07.2005
    Адрес
    Москва-Волгодонск
    Сообщений
    154
    Спасибо
    4
    Благодарностей: 24 : 5
    уже пробовал реакции никакой...кстате еще и 5800 точно такая же лежит... может сертификаты слетели подскажите как их заливать.

  6. #6
    Member
    Регистрация
    16.06.2008
    Адрес
    Казань
    Сообщений
    221
    Спасибо
    218
    Благодарностей: 58 : 14
    [Цитата = Ventil11; 1832148] уже пробовал реакции никакой ... кстате еще и 5800 точно такая же лежит ... может сертификаты слетели подскажите как их заливать. [/ quote]

    В смысле никакой реакции: не шьется или шьется, но не включается.

  7. #7
    Member
    Регистрация
    17.07.2005
    Адрес
    Москва-Волгодонск
    Сообщений
    154
    Спасибо
    4
    Благодарностей: 24 : 5
    шьеться но не вкл.

  8. #8
    Member
    Регистрация
    16.06.2008
    Адрес
    Казань
    Сообщений
    221
    Спасибо
    218
    Благодарностей: 58 : 14
    Какую ошибку выдает. Когда уфсом прошивал, ошибку выдавал какую нибудь. Выложи логи и закрой их BB кодом

  9. #9
    Member
    Регистрация
    17.07.2005
    Адрес
    Москва-Волгодонск
    Сообщений
    154
    Спасибо
    4
    Благодарностей: 24 : 5
    походу мне только RPL поможет. потому что IMEI 12345610654321?

  10. #10
    Member
    Регистрация
    16.06.2008
    Адрес
    Казань
    Сообщений
    221
    Спасибо
    218
    Благодарностей: 58 : 14
    [Цитата = Ventil11; 1832175] походу мне только RPL поможет. потому что IMEI 12345610654321? [/ quote]
    Походу ДА. Тебе трудно помочь, потому что ты сам не помогаешь. Нужно выложить логи: чек инфо прошивка, как телефон ведет себя сейчас после прошивки?

Похожие темы

  1. Galaxy Tab 10.1N P7501 Висит после неудачного обновления
    от Mihail_tm в разделе Samsung Software и Firmware
    Ответов: 7
    Последний ответ: 29.08.2012, 18:18
  2. 6233 после неудачного пргрева.
    от GangstaRAPPER в разделе Nokia для новичков
    Ответов: 93
    Последний ответ: 06.05.2011, 10:55
  3. J220 После неудачного ПО
    от XT-1 в разделе SonyEricsson для новичков
    Ответов: 3
    Последний ответ: 26.10.2010, 13:46
  4. I710 не включается после неудачного обновления PDA
    от Serg_new в разделе WinMo: КПК и Коммуникаторы
    Ответов: 12
    Последний ответ: 16.09.2010, 16:46
  5. Ответов: 2
    Последний ответ: 18.01.2007, 13:03

Социальные закладки

Социальные закладки

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •  
  Рейтинг@Mail.ru