CDMA ZTE Striker (S1602) восстановления boot-loader
CDMA ZTE Striker (S1602) восстановления boot-loader
12.04.2011
RIFF JTAG Update
RIFF JTAG Manager v1.30, RIFF Box Firmware v1.22 released
-добавлена поддержка CDMA моделей HTC Droid Eris, HTC Polaris (HTC Cruise)- разблокировка, восстановление загрузчика, восстановление IMEI, восстановление CID, восстановление ModelID .
-добавлена поддержка CDMA модели ZTE S1602 "MTS Striker" - восстановление загрузчика.
-обновлены DLL библиотеки для QUALCOMM NOR:
QSC1100_X14_NOR,
QSC60XX_L18_D08_NOR,
QSC60XX_L20_D08_NOR,
QSC60XX_L24_D08_NOR
-выпущены новые версии RIFF JTAG Manager v1.30 и RIFF Box Firmware v1.22
RIFF JTAG Manager v1.30:
-Исправлены ошибки при работе с ядром ARM7
RIFF Box Firmware v1.22:
-Добавлен запрос обработки DISABLE_POLLING от DCC загрузчика
Dood (19.04.2011), ribbentrop (19.04.2011)
20.04.2011
RIFF JTAG – JTAG Manager v1.31, добавлена функция "RUN / STOP"
RIFF Box Firmware v1.23 Добавлено 8/16/32-bit автоматическое чтение и запись ARM7 ядра режимы Thumb (использование GDBServer )
-CDMA Samsung SCH-S109 (MSM6000) Repair supported
RIFF JTAG – добавлены следующие модели
-CDMA Motorola W150i
-CDMA Haier C300
-CDMA Haier C3010, LG LSP450T
-CDMA Haier C2040
-CDMA Haier C5100
-CDMA Haier C6000
-CDMA ZTE C370
22.04.2011 HTC 7 Trophy T8686 (HTC Spark)-разблокировка, восстановление загрузчика, восстановление IMEI, восстановление CID, восстановление ModelID .
03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
vigo (04.05.2011)
Обновились :
04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported
Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.
To resurrect HTC Incredible C:
Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;
04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported
Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung I9023:
Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
04.05.2011 -Samsung Nexus S (i9023) Unbrick Boot repair supported
07.05.2011 -LG CU720 Shine Unbrick – Boot repair supported
10.05.2011 - CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported
12.05.2011 -Samsung Eternity A867 Unbrick - Boot repair supported
12.05.2011 - Huawei E5830 Broadband modem Unbrick – Boot repair supported
12.05.2011- Samsung Galaxy Ace S5830 Unbrick – Boot repair supported
13.05.2011 - Samsung Z630 Unbrick – Boot repair supported
- Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair
- CDMA Huawei C5589 Unbrick – Boot repair supported
AABBCC (14.05.2011)
20.05.2011 обновление
CDMA модели
* ZTE S160
* Unicare UN510BF
* Unicare ChivaC2
* Huawei C5100
Samsung
* Samsung S5250
* Samsung S5260 (Bug Fix)
10.06.2011 Подробнее, CDMA модели новые обновление,исправлены ошибки.
CDMA Models JTAG support :
* Huawei C2605
* Micromax MMX 250C
* ZTE WP829
* LG RD3640
Исправленные ошибки
* Samsung S5830
* HTC Incredible C
16.06.2011
RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair
Firmware 1.25
- Добавлено 5.0V USB Power On / Off управления функцией
- Изменилась последовательность для 32-битной записи данных для ARM11 ядра (MSM8xxx поддержки)
JTAG Manager 1.33
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.
- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.
- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)
- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.
- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)
- if error code 0x3C (write-protect) is received no recover attempts are made.
07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.
Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:
* Solder JTAG cable to HTC WildFireS JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC WildFireS is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.
Following CDMA models are supported from today :
* Samsung B139 Repair/Unbrick, Read/Write NOR Flash
* Samsung B259 Repair/Unbrick, Read/Write NOR Flash
* Samsung B309 Repair/Unbrick, Read/Write NOR Flash
* Samsung B319 Repair/Unbrick, Read/Write NOR Flash
* Samsung B379 Repair/Unbrick, Read/Write NOR Flash
* Samsung B619 Repair/Unbrick, Read/Write NOR Flash
* Huawei C31 Repair, Read/Write NOR flash