Nokia 5530 замена флеш

[K-Man]

Здравствуйте!
ТА пришел со стандартной проблемой, после полного стирания и проливки RPL ТА проработал 2 месяца.
Сейчас опять 180мА - 30мА и отключается. Решил поменять флеш, поставил с 5800 K5W2G1GACH (есть в рабочий ТА, в нем K5W2G1GAC0). Разметки под маленькую флеш нет на плате.

В итоге имею такой лог:
Лог чека по Fbus

Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101051105
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		19D0010803900052FD58D6AE4E8F0B62599F205A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	B8C3ADECFC997FCD8081D3DEAF870B8C
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.48.0, Algo: BB5
Prepare phone failed with message -> Failed to update Baudrate
Failed to Check BB5 Flashing Bus  -> Failed to Boot / Prepare Phone

Лог чека по USB

Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101051105
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		19D0010803900052FD58D6AE4E8F0B62599F205A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	B8C3ADECFC997FCD8081D3DEAF870B8C
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.48.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0xFFFFFFFF00000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.11.48.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Transmission Mode Requested: Control USB, Accepted: Control USB
Box TX2 Data Pin set to: Service Pin 3
Prepare phone failed with message -> Failed to set CMT Transmission Mode
Failed to Check BB5 Flashing Bus  -> Failed to Boot / Prepare Phone

Судя по второму логу, флеш видит. В чем может быть проблема?

[azis29]

До замены флешки какой лог был, проверил?

[K-Man]

До замены смотрел только по Fbus

Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101051105
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		19D0010803900052FD58D6AE4E8F0B62599F205A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	B8C3ADECFC997FCD8081D3DEAF870B8C
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.48.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
Prepare phone failed with message -> Failed to get CMT Configuration
Failed to Check BB5 Flashing Bus  -> Failed to Boot / Prepare Phone

[azis29]

Еще раз перекатать флешку, скорее всего криво сел!

[asrar]

Решил поменять флеш, поставил с 5800 K5W2G1GACH (есть в рабочий ТА, в нем K5W2G1GAC0).

А вы уверены что ваша флешка рабочая?

[K-Man]

После замены флеш на другую всё заработало. Проблема в самой флешке была..