Nokia X2-02 зависает на камере

[Undespoted]

Доброго времени суток...
Попался сия "девайс" с проблемой при открытии фотокамеры,зависает.телефону 2 недели от момента продажи.Следов удара или влаги нет,чист.
Phone Info>

Скрытый текст: Показать

Reading Phone Info....
Connected phone -    X2-02
Software ver : V 11.57 31-03-12 RM-694 (c) Nokia            
IMEI 1  :      353295*********
IMEI 2  :      353295*********
PPM     :      V 11.57 31-03-12 RM-694 (c) Nokia             F
CNT     :      Content: mh_059D1Q7 V 11.57 31-03-12 RM-694 (c) Nokia            
Product SN   :     405CCD2BI
Product code :     059N1T6
Base Prd.code:     059C943
Module code  :     0204922
Long Prod.SN :     0
Hardware info=======
HWID  : 2002
Batery: 4024 mV
CMT BT: 19e2-47026
LCDVer: TPO
Lock info ===========
IMEI       : 353295*********
IMEI spNet : 3A 35 92 05 95 43 81 04 
IMEI svNet : 33 35 92 05 95 43 81 04 F5 

Sl Conf  : 001-01-00000000000
Sl Prof  : 800000000003000-B
Sl Aux   : 000B0000
Hw Sig   : BE729F5A4143EBA5
Country      : Test SIM (Open)
Operator     : NOKIA (Open)

Lock info:
Block 1
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 2
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 3
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 4
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 5
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 6
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 7
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
CRT308 Backup Created

INFINEON : SuperDongle not exist (It is Ok)
CMLA Key status : Not Present
SimLock status : Ok
Security status : Ok
PA_SimLock Version : 
PA_SL3 phone ,  SP_CODE_LEN : 15
User Code : 12345
MMC pwd  : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery] 

Done!

Прошил:

Скрытый текст: Показать

Core : v1.53 , FlashEngine : v1.9

Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm694__11.79.mcusw
PPM : rm694__11.79.ppm_kz
CNT : rm694__11.79.image_kz_059D1N5
Flashing phone now...
Check files done...
->  Check SW version...
FlashFile version : 11.79
Phone version : 11.57 31-03-12 RM-694 (c) Nokia            
->  Check SW version : Upgrade
Backup CRT308 data...
CRT308 Backup Created
Check communication with phone....
ADL req restart
Communication verify done... Preparing...
Check communication with phone...

SL3 Simlock read (XGOLD) ... Ok
WMDRM Key read ... Ok

Reboot....
Connection opened successfully
DBG : F00A1FB300020303010100FF
CPUID : XGOLD 213
2nd boot Ok, 01
2nd ready, AA
Sending Algo
Algo sent Ok
BL : Quantum_Bootloader_10.46_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!
Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 353295*********
IMEI 2 : 353295*********
PCcode : Ћќ	СљЇ

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
SimLock Data saved...
SimLock Key saved...
WMDRM_PD Data saved...

RPL saved : D:\InfinityBox\BEST\Backup\Cert\*******************


   ===Flashing [MCU]===
File : rm694__11.79.mcusw
Image : rm694__11.79.mcusw_ebl_psi.fls
Cert block found, sending....
Cert sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ... 
Erase done, time : 00:00:05 
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01980000
Erasing, wait ... 
Erase done, time : 00:02:24 
Write , Start : 0x40280000 , Len : 0x01900000
Flashing , wait ...
Region flash done, time : 00:00:34
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ... 
Erase done, time : 00:00:00 
No write data, skip

   ===Flashing [PPM]===
File : rm694__11.79.ppm_kz
Image : package_kz.ppm_ebl_psi.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41C00000 , Len : 0x00700000
Erasing, wait ... 
Erase done, time : 00:00:26 
Write , Start : 0x41C00000 , Len : 0x003E453C
Flashing , wait ...
Region flash done, time : 00:00:04

   ===Flashing [CNT]===
File : rm694__11.79.image_kz_059D1N5
Image : package_kz_059D1N5.image.fls
Cert block found, sending....
Cert sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x42300000 , Len : 0x01B20000
Erasing, wait ... 
Erase done, time : 00:02:56 
Write , Start : 0x42300000 , Len : 0x00E40000
Flashing , wait ...
Region flash done, time : 00:00:17
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ... 
Erase done, time : 00:00:05 
No write data, skip

Flashing done!
Total flash time : 00:06:58
Reboot phone now...

Reading Phone Info....
Connected phone -   X2-02
Software Info:     V 11.79 15-08-12 RM-694 (c) Nokia            
IMEI:  35329**********
PPM version :   V 11.79 15-08-12 RM-694 (c) Nokia             KZ
Product code:  059N1T6
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
Product code update...
Resetting LifeTimer
Check phone mode...
Phone in Test mode
Seting Local mode... wait...
Local mode set
Reset Done!
Checking User Certificates...
Total - 43 certs
Data exist, skip certificate repair...
Battery voltage is enough for start
Set phone to Normal mode...

DCC

Скрытый текст: Показать

Try Read Camera Configuration to base...

Camera HW : 0A350160
Configuration saved Ok

Cam 2 configuration not found

Done!

Checking Camera Configuration...
Operating mode is OK, no need change...

CAM1 HW : 0A350160
CAM1 SW ver : 006015
Updating Camera #1 Configuration...
Upload done, checking...
CAM1 SW ver : 006015
Configuration Ok!

Селф тест

Скрытый текст: Показать

Initializing Tests...
IMEI : 3532********* , Phone : RM-694 X2-02
Get keys...
PASSED | ST_SIM_LOCK_TEST
PASSED | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_LCD_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
MINOR | ST_CAMERA_IF_TEST
PASSED | ST_BT_WAKEUP_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_CDSP_PA_TX_POWER_TEST
PASSED | ST_SLEEP_CLOCK_FREQ_TEST
PASSED | ST_KEYB_LINE_TEST
PASSED | ST_ADC_IF_TEST
PASSED | ST_MEMORY_CARD_IF_TEST
PASSED | ST_SIM_MULTIPLEXER_IF_TEST
PASSED | ST_RF_PLL_TEST
PASSED | ST_SECURITY_FUSE_TEST
->ERROR | ST_FMTX_ANTENNA_TEST
SelfTests end
Done!

Камеру менял от 2700с
PM с авторизацией есть смысл лить в етого икс голда?
А сегодня выдало

Checking Camera Configuration...
Operating mode is OK, no need change...

CAM1 HW : 0A021001
CAM1 SW ver : XXXXXX [ SW damaged ]
Configuration 0A021001.dcc not found... :(
Secondary Camera #2 configuration info not exist

[Prodrive]

Пробивал менять?

[elenlove]

Между камерой и процом, стоит микруха N3000. Вот ее и пробуйте перекатать. Также проверьте ее обвязку.
Ну а первым делом напряжения питания камеры и N3000 проверьте.

[Undespoted]

На камере было 1.78 напруга.После Прогрев n3000,при входе в камеру выдал "Операция не выполнена".Поставил на место камеру родную-Заработала.

Initializing Tests...
IMEI : 353295******** , Phone : RM-694 X2-02
Get keys...
PASSED | ST_SIM_LOCK_TEST
PASSED | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_LCD_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
PASSED | ST_CAMERA_IF_TEST
PASSED | ST_BT_WAKEUP_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_CDSP_PA_TX_POWER_TEST
PASSED | ST_SLEEP_CLOCK_FREQ_TEST
PASSED | ST_KEYB_LINE_TEST
PASSED | ST_ADC_IF_TEST
PASSED | ST_MEMORY_CARD_IF_TEST
PASSED | ST_SIM_MULTIPLEXER_IF_TEST
PASSED | ST_RF_PLL_TEST
PASSED | ST_SECURITY_FUSE_TEST
->ERROR | ST_FMTX_ANTENNA_TEST
SelfTests end

Легко отделался,видать ударчик всё таки был!
Прикрепляю схему,на форуме не нашёл.
Всем спасибо за помощ