KMVTU000LM-B503 vs EasyJTAG

[asg-gealt]

Всем привет
Народ, кто много работал с этими emmc гляньте лог - что с ней не так.
(была восстановлена из emmc name: 0000, теперь потребление скачет со 150 до 250 мА в цикле,признаков жизни нет, процедура восстановления обычная - repair name дважды, формат, правка размеров user area и boot, прошивка юзер и бут, проверял - проливается нормально, не мусором):

Z3X EasyJtag Software ver. 1.6.2.1
Loading eMMC Addon Firmware... IO: 1850 mV
CMD Pullup Level:1722 mV
CMD Active Level:1784 mV
eMMC Device Information
EMMC CID : 15010056545530304DF103C571327FEC
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 63271218
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_ 63271218_20150103_1310.extcsd
Searching for partition tables...
Detected GPT over MBR...
Warning: Header Size = 512 (expected 92)
Medium UUID: 52444E41-494F-2044-4D4D-43204449534B
Warning: Entries Count = 128
MMCBLK0P0 (BOTA0) Range: [0X400000,0] ,Len: 7FFE00
MMCBLK0P1 (BOTA1) Range: [0X800000,0] ,Len: BFFE00
MMCBLK0P2 (EFS) Range: [0XC00000,0] ,Len: 1FFFE00
MMCBLK0P3 (PARAM) Range: [0X2000000,0] ,Len: 27FFE00
MMCBLK0P4 (BOOT) Range: [0X2800000,0] ,Len: 2FFFE00
MMCBLK0P5 (RECOVERY) Range: [0X3000000,0] ,Len: 37FFE00
MMCBLK0P6 (RADIO) Range: [0X3800000,0] ,Len: 57FFE00
MMCBLK0P7 (CACHE) Range: [0X5800000,0] ,Len: 457FFE00
MMCBLK0P8 (SYSTEM) Range: [0X45800000,0] ,Len: A57FFE00
MMCBLK0P9 (HIDDEN) Range: [0XA5800000,0] ,Len: C87FFE00
MMCBLK0P10 (OTA) Range: [0XC8800000,0] ,Len: C8FFFE00
MMCBLK0P11 (USERDATA) Range: [0XC9000000,0] ,Len: AAFFFE00
Done...Presets has been updated...
Done.

Z3X EasyJtag Software ver. 1.6.2.1
Loading eMMC Addon Firmware... IO: 1850 mV
CMD Pullup Level:1742 mV
CMD Active Level:1804 mV
eMMC Device Information
EMMC CID : 15010056545530304DF103C571327FEC

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N:   63271218
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
Backup saved: VTU00M_  63271218_20150103_1310.extcsd
=============================================

  Extended CSD rev 1.6 (MMC 4.5)

=============================================


Card Supported Command sets [S_CMD_SET: 0x01]

HPI Features [HPI_FEATURE: 0x01]: 
implementation based on CMD13

Background operations support [BKOPS_SUPPORT: 0x01]

Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]

Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]

Data TAG support [DATA_TAG_SUPPORT: 0x01]

Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]

Tag Resources Size [TAG_RES_SIZE: 0x00]

Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]

Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]

Extended partition attribute support [EXT_SUPPORT: 0x03]

Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]

Power off notification [POWER_OFF_LONG_TIME: 0x3c]

Cache Size [CACHE_SIZE] is 65536 KiB

Background operations status [BKOPS_STATUS: 0x00]

1st Initialisation Time after programmed sector [INI_TIMEOUT_AP: 0x1e]

Power class for 52MHz, DDR at 3.6V [PWR_CL_DDR_52_360: 0x00]

Power class for 52MHz, DDR at 1.95V [PWR_CL_DDR_52_195: 0x00]

Power class for 200MHz at 3.6V [PWR_CL_200_360: 0x00]

Power class for 200MHz, at 1.95V [PWR_CL_200_195: 0x00]

Minimum Performance for 8bit at 52MHz in DDR mode:

 [MIN_PERF_DDR_W_8_52: 0x00]

 [MIN_PERF_DDR_R_8_52: 0x00]

TRIM Multiplier [TRIM_MULT: 0x02]

Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]

Boot Information [BOOT_INFO: 0x07]

 Device supports alternative boot method

 Device supports dual data rate during boot

 Device supports high speed timing during boot

Boot partition size [BOOT_SIZE_MULTI: 0x10]

Access size [ACC_SIZE: 0x07]

High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]

High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]

Reliable write sector count [REL_WR_SEC_C: 0x01]

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x50]

Sleep current (VCC) [S_C_VCC: 0x07]

Sleep current (VCCQ) [S_C_VCCQ: 0x07]

Sleep/awake timeout [S_A_TIMEOUT: 0x11]

Sector Count [SEC_COUNT: 0x01d5a000]

Minimum Write Performance for 8bit:

 [MIN_PERF_W_8_52: 0x00]

 [MIN_PERF_R_8_52: 0x00]

 [MIN_PERF_W_8_26_4_52: 0x00]

 [MIN_PERF_R_8_26_4_52: 0x00]

Minimum Write Performance for 4bit:

 [MIN_PERF_W_4_26: 0x00]

 [MIN_PERF_R_4_26: 0x00]

Power classes registers:

 [PWR_CL_26_360: 0x00]

 [PWR_CL_52_360: 0x00]

 [PWR_CL_26_195: 0x00]

 [PWR_CL_52_195: 0x00]

Partition switching timing [PARTITION_SWITCH_TIME: 0x01]

Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x02]

I/O Driver Strength [DRIVER_STRENGTH: 0x00]

Card Type [CARD_TYPE: 0x07]

CSD structure version [CSD_STRUCTURE: 0x02]

Command set [CMD_SET: 0x00]

Command set revision [CMD_SET_REV: 0x00]

Power class [POWER_CLASS: 0x00]

High-speed interface timing [HS_TIMING: 0x00]

Erased memory content [ERASED_MEM_CONT: 0x00]

Boot configuration bytes [PARTITION_CONFIG: 0x48]

 No access to boot partition

Boot config protection [BOOT_CONFIG_PROT: 0x00]

Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]

High-density erase group definition [ERASE_GROUP_DEF: 0x00]

Boot write protection status registers [BOOT_WP_STATUS]: 0x00

Boot Area Write protection [BOOT_WP]: 0x00

Power ReadOnly locking: possible

Permanent ReadOnly locking: possible

Read Only lock status: not locked

User area write protection register [USER_WP]: 0x00

FW configuration [FW_CONFIG]: 0x00

RPMB Size [RPMB_SIZE_MULT]: 0x01

Write reliability setting register [WR_REL_SET]: 0x1f

Write reliability parameter register [WR_REL_PARAM]: 0x05

Enable background operations handshake [BKOPS_EN]: 0x00

H/W reset function [RST_N_FUNCTION]: 0x00

HPI management [HPI_MGMT]: 0x00

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

 Device support partitioning feature

 Device can have enhanced tech.

Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0000bb

Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

General Purpose Partition Size
 [GP_SIZE_MULT_4]: 0x000000

 [GP_SIZE_MULT_3]: 0x000000

 [GP_SIZE_MULT_2]: 0x000000

 [GP_SIZE_MULT_1]: 0x000000

Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000

Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000

Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00

Periodic Wake-up [PERIODIC_WAKEUP]: 0x00

Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[127]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[126]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[125]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[124]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[123]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[122]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[121]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[120]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[119]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[118]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[117]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[116]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[115]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[114]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[113]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[112]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[111]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[110]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[109]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[108]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[107]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[106]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[105]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[104]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[103]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[102]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[101]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[100]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[99]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[98]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[97]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[96]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[95]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[94]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[93]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[92]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[91]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[90]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[89]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[88]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[87]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[86]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[85]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[84]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[83]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[82]]: 0x0c

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[81]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[80]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[79]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[78]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[77]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[76]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[75]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[74]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[73]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[72]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[71]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[70]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[69]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[68]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[67]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[66]]: 0x08

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[65]]: 0x00

Vendor Specific Fields [VENDOR_SPECIFIC_FIELD[64]]: 0x03

Native sector size [NATIVE_SECTOR_SIZE]: 0x00

Sector size emulation [USE_NATIVE_SECTOR]: 0x00

Sector size [DATA_SECTOR_SIZE]: 0x00

1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00

Class 6 commands control [CLASS_6_CTRL]: 0x00

Number of addressed group to be Released[DYNCAP_NEEDED]: 0x00

Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000

Exception events status[EXCEPTION_EVENTS_STATUS]: 0x0000

Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000

Context configuration [CONTEXT_CONF[51]]: 0x00

Context configuration [CONTEXT_CONF[50]]: 0x00

Context configuration [CONTEXT_CONF[49]]: 0x00

Context configuration [CONTEXT_CONF[48]]: 0x00

Context configuration [CONTEXT_CONF[47]]: 0x00

Context configuration [CONTEXT_CONF[46]]: 0x00

Context configuration [CONTEXT_CONF[45]]: 0x00

Context configuration [CONTEXT_CONF[44]]: 0x00

Context configuration [CONTEXT_CONF[43]]: 0x00

Context configuration [CONTEXT_CONF[42]]: 0x00

Context configuration [CONTEXT_CONF[41]]: 0x00

Context configuration [CONTEXT_CONF[40]]: 0x00

Context configuration [CONTEXT_CONF[39]]: 0x00

Context configuration [CONTEXT_CONF[38]]: 0x00

Context configuration [CONTEXT_CONF[37]]: 0x00

Packed command status [PACKED_COMMAND_STATUS]: 0x00

Packed command failure index [PACKED_FAILURE_INDEX]: 0x00

Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00

Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00

Searching for partition tables...
Detected GPT over MBR...
Warning: Header Size = 512 (expected 92)
Medium UUID: 52444E41-494F-2044-4D4D-43204449534B
Warning: Entries Count = 128
MMCBLK0P0 (BOTA0) Range:	[0X400000,0] ,Len: 7FFE00
MMCBLK0P1 (BOTA1) Range:	[0X800000,0] ,Len: BFFE00
MMCBLK0P2 (EFS) Range:	[0XC00000,0] ,Len: 1FFFE00
MMCBLK0P3 (PARAM) Range:	[0X2000000,0] ,Len: 27FFE00
MMCBLK0P4 (BOOT) Range:	[0X2800000,0] ,Len: 2FFFE00
MMCBLK0P5 (RECOVERY) Range:	[0X3000000,0] ,Len: 37FFE00
MMCBLK0P6 (RADIO) Range:	[0X3800000,0] ,Len: 57FFE00
MMCBLK0P7 (CACHE) Range:	[0X5800000,0] ,Len: 457FFE00
MMCBLK0P8 (SYSTEM) Range:	[0X45800000,0] ,Len: A57FFE00
MMCBLK0P9 (HIDDEN) Range:	[0XA5800000,0] ,Len: C87FFE00
MMCBLK0P10 (OTA) Range:	[0XC8800000,0] ,Len: C8FFFE00
MMCBLK0P11 (USERDATA) Range:	[0XC9000000,0] ,Len: AAFFFE00
Done...Presets has been updated...
Done.

[azis29]

Все процедуры правильно. Скорее всего дохлый emmc ..Несколько раз встречался все пишется на ура но не стартует..

[asg-gealt]

Вернемся к вопросу. Телефон тот же. Флэшки от S3 закончились и новые и с доноров, а нужно срочно. Поставил KMVTU000LM-B503 (от I9500, донор). На данный момент пролил только ROM2 (BOOT) от I9300 с саппорта, через DirectEMMC в EasyJTAG. Тело висит на заставке (разумеется), в бут входит. В буте product name I9300, счетчик кастомов - 4 (нормально). Многофайловую шить не хочет, Odin висит на "Get PIT for mapping". Размеры разделов пока не менял на флэшке, то есть они выглядят как на S4:

EMMC NAME: V3W00M , S/N: 4272537099
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB

Флэхи с донора, причем с другой модели так еще не ставил. Вопрос - что делать дальше, не хочу убить последнюю флэшку)
Пробовать прошить с пит-файлом и репартишеном от I9300, или пит oт I9500? Надо ли менять загрузочные разделы и RPBM под S3 или оставить так?
Заранее спасибо.

[tps7900]

в бут входит

дай всю инфу что пишет в режиме bootloader

[IDLeon]

Флэхи с донора, причем с другой модели так еще не ставил. Вопрос - что делать дальше, не хочу убить последнюю флэшку)
Пробовать прошить с пит-файлом и репартишеном от I9300, или пит oт I9500?

С easyjtag не знаю, нет в наличии, но когда с другой модели ставил, то восстанавливал бут i9300 с флешки (замкнув r313) - проливал bl c выбранным pit от i9300. После чего перезагружал в бутлоадер и прошивал 4х файловую. Если потом при включении стопорился на Samsung, то еще проливал одином чистый efs.

[azis29]

Саня, чего боятся? Зайди в раздел
Custom Operation-> Samsung: MoviNAND Format and Reset
Custom Operation-> samsung: MoviNAND Format and Reset
Если конфиг правильно. ( в твоем случай правильно)
Пролей Rom_1, Rom_2 с суппорта, прошей с pit файлом многофайловую прошивки, далее сброс efs, root, правка имея..
Всегда от донора ставил так и ни каких проблем..
ЗЫ..Если хочешь менять разделы rom_2, rom_3 то меняется без проблем..В аське могу подсказать, для начало так проверь..

[asg-gealt]

дай всю инфу что пишет в режиме bootloader

ODIN MODE
Product name: GT-I9300
CUSTOM BINARY DOWNLOAD: Yes (4 counts)
CURRENT BINARY: Custom
sYSTEM STATUS: Custom

[asg-gealt]

ТА готов:
MoviNAND Factory Format (extcd из бэкапа не восстанавливаем)
MoviNAND Format and Reset (extcd из бэкапа не восстанавливаем)
Меняем размеры ROM 2\3 на 2mb
Меняем размер RPBM на 128kb
Set i9300 boot config
Прошиваем ROM1 (512mb)
Прошиваем ROM2 (2mb)
Прошиваем многофайловую
Repair EFS
Root
Восстанавливаем IMEI

Спасибо Азизу (azis29) за совет, не восстанавливать extcd.